Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 146
Search took 0.01 seconds.
Search: Posts Made By: hotrodart
Forum: Late V8 (1954+) 11-18-2020, 03:19 PM
Replies: 2
Views: 148
Posted By hotrodart
Re: Cork Gasket on Fuel Level Sender

I have never used a sealant on those cork gaskets, never had a leak issue.....make sure the surfaces are clean metal......do not know what Ford factories did though. I just tighten the screws, no...
Forum: Early V8 (1932-53) 11-03-2020, 03:10 PM
Replies: 12
Views: 435
Posted By hotrodart
Re: 1940 Ford fuel gauge issue

I have a similar issue on my '40 coupe......stock gauge/resistor with aftermarket sender. I am told the aftermarket senders operate on a different principle and cannot ever be accurate. Best bet is...
Forum: Early V8 (1932-53) 10-24-2020, 02:52 PM
Replies: 8
Views: 531
Posted By hotrodart
Re: storage

I used to close the windows and put the cover on, and use repellent inside my cars. But....the mice still got inside and under the hood. So, I tried leaving the windows down, hood and trunk open,...
Forum: Early V8 (1932-53) 10-15-2020, 02:10 PM
Replies: 3
Views: 374
Posted By hotrodart
Re: Gear ratio on rearend

9 is the number of teeth on the pinion gear, 34 is the number of teeth on the ring gear. Divide 9 into 34 to get your rear axle ratio: 3.78 nominal (3.777777777 actual)
Forum: Early V8 (1932-53) 10-14-2020, 02:20 PM
Replies: 3
Views: 532
Posted By hotrodart
Re: Anything on the threads?

I use anti-seize compound for brass fittings into aluminum. Been doing that for 60 years without issues. If the fitting is a gauge sender, the Teflon tape might insulate it and it may not function....
Forum: Model A (1928-31) 10-07-2020, 06:42 PM
Replies: 18
Views: 1,349
Posted By hotrodart
Re: Luray Swap meet

I was there yesterday and today......very small......vendors were packing up at 10 AM today.......very few people this morning.......a bit disappointing, but still nice to get out with car guys.......
Forum: Early V8 (1932-53) 10-06-2020, 02:54 PM
Replies: 1
Views: 143
Posted By hotrodart
Re: Mid atlantic model T meet 6 and 7 October in Luray, VA

I was there this morning......about 40 or so vendors, mostly Model T (of course!), small bit of V-8 stuff, small crowd. Was done in about an hour....might go back Wednesday to see if more vendors...
Forum: Model A (1928-31) 10-02-2020, 02:56 PM
Replies: 21
Views: 936
Posted By hotrodart
Re: Rear Axle Taper - What It Does

Your skepticism of the axle preload specification is way off base. You have been lucky with only 50 ft-lbs....or maybe you simply "baby" your car.



The taper on the axle is designed by the...
Forum: Early V8 (1932-53) 10-02-2020, 02:26 PM
Replies: 10
Views: 363
Posted By hotrodart
Re: Gas Tank Fuel Gauge reading question

The accuracy of the 80 year old technology in that gauge is significantly less than the measurable difference in the float levels with those specific liquids.
Forum: Model A (1928-31) 09-14-2020, 01:57 PM
Replies: 19
Views: 642
Posted By hotrodart
Re: how many tie rod turns equates to 1/16 inch toe in change ?

Interesting question, but it is not the correct one if you are looking for the correct method to adjust toe-in/toe-out. Depending on the actual toe-in/toe-out on the car, you need to rotate the tie...
Forum: Early V8 (1932-53) 09-10-2020, 03:12 PM
Replies: 25
Views: 824
Posted By hotrodart
Re: Hydraulic Brake Light Switch

Before you finalize your choice of MC.....I used a BOSS 429 MC (15/16" bore) on my '40 coupe (disc fronts).......I had to "section" the cover to clear the floorboard.....also had to lengthen the push...
Forum: Model A (1928-31) 09-09-2020, 02:50 PM
Replies: 13
Views: 980
Posted By hotrodart
Re: Toe-In Lesson Learned

I did mine with a tape measure, then put it on a 4-wheel laser machine......the old way was right on the money.
Forum: Early V8 (1932-53) 09-07-2020, 03:02 PM
Replies: 20
Views: 1,013
Posted By hotrodart
Re: No Oil Pressure in 8BA

Good lesson in this thread....I pull apart every engine.....new crates as well as previously owned/run. That's the only way to know what you have. There are usually a few surprises in every...
Forum: Early V8 (1932-53) 09-04-2020, 02:34 PM
Replies: 4
Views: 273
Posted By hotrodart
Re: Best source for glass?

I got glass pieces from a junk yard and cut my own. Used the old pieces as patterns. Not difficult to do.
Forum: Late V8 (1954+) 08-24-2020, 02:50 PM
Replies: 12
Views: 673
Posted By hotrodart
Re: Transmission change

You might want to change out the




I did this swap (many years ago) and found it to be quite easy and straight forward. I bought a parts car and simply swapped over all the needed parts, and...
Forum: Early V8 (1932-53) 08-21-2020, 02:44 PM
Replies: 32
Views: 2,071
Posted By hotrodart
Re: PERTRONIX Ignitor Ignition 1940 ford Helmet Dist

The Pertronix techs used to say to not use their Ignitor with a generator.....to much "noise" from the brushes and voltage spikes would blow it out.....maybe they made some electronics changes?......
Forum: Early V8 (1932-53) 08-21-2020, 02:31 PM
Replies: 20
Views: 1,040
Posted By hotrodart
Re: Which is easier

I have always pulled the axle to remove the trans.......never even thought about pulling the engine......axle out seems easier to me......
Forum: Early V8 (1932-53) 08-19-2020, 02:43 PM
Replies: 27
Views: 1,616
Posted By hotrodart
Re: I found a crack in an odd place while pressure testing

The military uses DEVCON on diesel engine cracks like yours.......works great and lasts a long time. I have used it with excellent results.
Forum: Early V8 (1932-53) 08-19-2020, 02:35 PM
Replies: 11
Views: 590
Posted By hotrodart
Re: Drake's Gas Tank In A "35

I put a stainless Drake tank in my '40 coupe 3 years ago.....pretty much the same frame as your '35. It went in very quickly/easily without needing to raise the body. No issues at all with fit or...
Forum: Early V8 (1932-53) 08-06-2020, 03:27 PM
Replies: 14
Views: 769
Posted By hotrodart
Re: Shocks are bottomed out

I have a 4" dropped axle on my '40 coupe with a Posies reverse eye spring....pretty much the same set up as your '41 PU.....I used "stock" Gabriel replacement '48 Ford shocks with the "old style"...
Forum: Early V8 (1932-53) 08-03-2020, 02:32 PM
Replies: 17
Views: 787
Posted By hotrodart
Re: Drake '40 tank

I guess your experience with these conflicts with mine (and others) .......the Drake tank fit in perfectly with the body NOT REMOVED. A very easy, quick replacement.
Forum: Early V8 (1932-53) 07-30-2020, 02:21 PM
Replies: 9
Views: 443
Posted By hotrodart
Re: Turn Signal Kit ?

The wiring and fuse need to be matched for 6 volts (heavier gage)....the bulbs take 2X the anps as 12 volt bulbs.
Forum: Early V8 (1932-53) 07-26-2020, 02:25 PM
Replies: 7
Views: 357
Posted By hotrodart
Re: Disk brakes

I agree with COOP entirely......I have disc fronts, Ford drum rears on my "40 coupe. It would be foolish to not change the MC for one that is designed to this purpose. I used a BOSS 429 MC (15/16...
Forum: Early V8 (1932-53) 07-26-2020, 02:16 PM
Replies: 17
Views: 787
Posted By hotrodart
Re: Drake '40 tank

I put a Drake stainless tank in my '40 coupe......zero issues with fit......entire exercise took about 2, maybe 3 hours......on my back in the shop, with the car on 12 inch high ramps.. I did not...
Forum: Early V8 (1932-53) 07-16-2020, 02:28 PM
Replies: 38
Views: 1,902
Posted By hotrodart
Re: Fan came apart!!

This is a text book metal fatigue failure........these fans go through millions of cycles in the 70+ years of operating........they are not precision balanced, nor precision machined and do not have...
Showing results 1 to 25 of 146

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:15 PM.