Forum: Early V8 (1932-53)
07-10-2017, 09:38 PM
|
Replies: 25
Views: 4,118
|
Forum: Early V8 (1932-53)
03-25-2017, 12:01 AM
|
Replies: 69
Views: 26,581
Re: Isky 404A cam - Harley Davidson grind?
Hi if you are still grinding i have a 8cm cam what can you do with that?? 1007b or potvin 3/8 its going in a 49 f100 .060 merc w. 350 holley 2 bbl... suggestions?? ive noticed the...
|
Forum: Early V8 (1932-53)
02-25-2014, 11:33 PM
|
Replies: 25
Views: 8,333
Re: Flathead to T5 help needed
On those truck bells no adaptor needed weld a couple thick lugs where needed drill and tap the chev bolt patteren and finally mill 1/8 of the surface that should give enough purchase
|
Forum: Early V8 (1932-53)
01-06-2014, 12:27 AM
|
Replies: 5
Views: 1,648
Re: glass removal
The chromes stay in the rubber when removing, push out from the inside working the rubber off the body with a hook tool as u push if stuck on adhesive wd 40 does soften the glue when...
|
Forum: Early V8 (1932-53)
12-04-2013, 11:13 PM
|
Replies: 2
Views: 1,062
|
Forum: Early V8 (1932-53)
11-17-2013, 11:26 PM
|
Replies: 7
Views: 1,631
Re: windshield installation of 46/68
bill is right chrome after but if u cant get the center bar in the glass either has to move out to the side or it is too wide and will have to be ground repop rubbers are no fun Rick
|
Forum: Model A (1928-31)
08-19-2013, 11:04 PM
|
Replies: 4
Views: 1,849
Re: Windshield install
try little one inch pieces until you find the one that will go to gether without too much force, i tape the rubber to the glass with electrcal tape rub some motor oil on outside of tape it makes...
|
Forum: Early V8 (1932-53)
08-18-2013, 11:28 PM
|
Replies: 1
Views: 1,318
94 Carbs
Someone should know what the CFM would be on a a pair of 94 carbs,,,bin thinkin of trying a 500 holley 2 bbl jetted down
|
Forum: Early V8 (1932-53)
08-15-2013, 09:36 PM
|
Replies: 7
Views: 1,671
|
Forum: Early V8 (1932-53)
08-13-2013, 11:12 PM
|
Replies: 44
Views: 82,895
|
Forum: Early V8 (1932-53)
08-10-2013, 02:04 AM
|
Replies: 2
Views: 1,453
Dwell
Wuz wondering what dwell to set on the Bubbas chev 8ba conversion, same as sbc at 30 or what,,, Rick
|
Forum: Early V8 (1932-53)
06-24-2013, 10:54 PM
|
Replies: 3
Views: 1,586
Re: Door glass removal 39 pkup
Window in up position loosen regulator screws (4) push it into door and crank and slide the arms out of the holes in the slots
|
Forum: Early V8 (1932-53)
06-24-2013, 11:51 AM
|
Replies: 3
Views: 1,343
|
Forum: Early V8 (1932-53)
06-23-2013, 11:29 PM
|
Replies: 3
Views: 1,343
34 2dr doorglass
Hey guys does someone have measurements for location of the steel channel on the door glass we put this thing together with it centered now glass wants to tilt and bind up?????? this car does not...
|
Forum: Early V8 (1932-53)
05-07-2013, 12:47 AM
|
Replies: 44
Views: 82,895
|
Forum: Early V8 (1932-53)
04-28-2013, 12:28 PM
|
Replies: 6
Views: 1,895
F1 headers
Has anyone used Macs auto 48 to 52 F1 headers do they fit without hammering?? Rick
|
Forum: Early V8 (1932-53)
03-11-2013, 11:33 AM
|
Replies: 10
Views: 2,178
Re: headers
Reds headers has a 3 into a collector style for the 48 to 52 f1 $250
|
Forum: Early V8 (1932-53)
02-28-2013, 12:56 AM
|
Replies: 8
Views: 11,001
Re: lowering a 1949 ford f1
Ive got the same problem with a stock 49 f1 was going to take the springs to a springshop to dearch and take out every other leaf. Is there a source for a reversed eye mainleaf??
|
Forum: Early V8 (1932-53)
02-12-2013, 11:17 PM
|
Replies: 22
Views: 9,024
Re: 1935 Door Glass Off Track
I hope you have both those bolt on studs tat run in that slot to make the glass track properly also critical where you put the channel on the glass
|
Forum: Early V8 (1932-53)
02-12-2013, 11:08 PM
|
Replies: 4
Views: 1,202
Re: 37 Rear window seal
Hey dont use too small of a string, if using new rubbers no lube nesscesary.. you can alson use a hook tool to pull the rubber over dont push too hard untill its all started
|
Forum: Early V8 (1932-53)
02-10-2013, 09:58 PM
|
Replies: 13
Views: 8,449
Re: Windshield glass setting tape
heres the drill fold the tape into the lower half of frame with large piecut at the center post the radius bend gets a few piecuts then motor oil on the tape to slide the glass in easier on the...
|
Forum: Late V8 (1954+)
01-13-2013, 11:01 PM
|
Replies: 12
Views: 6,509
|
Forum: Early V8 (1932-53)
01-11-2013, 11:33 PM
|
Replies: 53
Views: 19,678
|
Forum: Early V8 (1932-53)
01-05-2013, 01:13 AM
|
Replies: 27
Views: 5,715
|
Forum: Early V8 (1932-53)
01-05-2013, 01:07 AM
|
Replies: 163
Views: 62,545
|