Forum: Early V8 (1932-53)
07-27-2022, 08:49 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-27-2022, 06:54 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-27-2022, 12:16 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-26-2022, 07:28 PM
|
Replies: 24
Views: 3,673
Re: Drive shaft housing forward bearing size ?
Wow "eureka" I thought it was a OEM , Thanks , Maybe I can modify it with a ground out dimple, There's a little bit of shoulder to mic next to the OD of bearing, and it mics similar to the B-4655...
|
Forum: Early V8 (1932-53)
07-25-2022, 05:30 PM
|
Replies: 24
Views: 3,673
Re: Drive shaft housing forward bearing size ?
I got the those numbers with a T gauge and micrometer.. the yellow outline( i'm not a photoshop expert) is the bushing I'm measuring to get the ID. So I guess it appears someone has machined a thick...
|
Forum: Early V8 (1932-53)
07-25-2022, 12:26 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-25-2022, 12:24 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-24-2022, 07:35 PM
|
Replies: 24
Views: 3,673
|
Forum: Early V8 (1932-53)
07-24-2022, 07:31 PM
|
Replies: 24
Views: 3,673
Drive shaft housing forward bearing size ?
Have a DS housing with a 1.47" bearing ID, has no seam ,no hole, what model would this be ? . Its 72" long , Got this DS for my Hotrod project , but cant find any bearings listed for this ID.. the...
|
Forum: Early V8 (1932-53)
08-15-2019, 06:16 PM
|
Replies: 2
Views: 943
Drive shaft welding considerations?
Getting ready to shorten my solid 42 D/S, are there any special considerations (besides cooling slowly) when welding coupler on or machining new splines ?.
what is the metal composition of D/S ...
|
Forum: Early V8 (1932-53)
07-24-2019, 09:24 PM
|
Replies: 8
Views: 1,468
Re: ridges on brake drum ?
Did chisel them off , big hammer, were spot welded in center, will get them spacers..thk/s for all info..gus.
|
Forum: Early V8 (1932-53)
07-24-2019, 03:24 PM
|
Replies: 2
Views: 932
|
Forum: Early V8 (1932-53)
07-24-2019, 12:31 PM
|
Replies: 8
Views: 1,468
Re: ridges on brake drum ?
Bingo ,Yes trying to nest 35s , these aren't lead?? ,how are they attached ? so we get out the chisel? thk/u. gus..
|
Forum: Early V8 (1932-53)
07-23-2019, 10:24 PM
|
Replies: 8
Views: 1,468
ridges on brake drum ?
1)12" drum 5x5-1/2 , highlighted are ridges (only 1/3 are attached) which prevent rim from mounting correctly ,what use are these ridges ?
2) also have 11 " 5x5-1/2, drums similar,but no nested...
|
Forum: Early V8 (1932-53)
07-22-2019, 07:30 PM
|
Replies: 5
Views: 1,386
|
Forum: Early V8 (1932-53)
07-22-2019, 04:58 PM
|
Replies: 5
Views: 1,386
Re: 42 Pass. torque tube angle (stock) ?
Great info ,thanks, since I am still in the mock-up stage of this rod project ,I think i will raise up the engine/trans for a couple deg. for a + up on pinion angle ..
I would still like to know...
|
Forum: Early V8 (1932-53)
07-19-2019, 06:53 PM
|
Replies: 5
Views: 1,386
42 Pass. torque tube angle (stock) ?
I'm mocking up my ride ..Have 8BA/39 trans mating up to a 42 ford rear end with stock torque tube . Have the motor at 3deg for level carb, motor is mounted on the low end of the scale right now ( ...
|
Forum: Early V8 (1932-53)
07-02-2019, 01:19 PM
|
Replies: 6
Views: 1,234
Re: rear spring ID?
thanks all for input ,spring is 42 ,and found bushings at C&G , great resource, thanks for your time ,gus..
|
Forum: Early V8 (1932-53)
06-30-2019, 06:25 PM
|
Replies: 6
Views: 1,234
Re: rear spring ID?
It was a Ebay hot rod in a "basket" project .lots of miss matched parts , I think the axcel might be a 37-41 ,but I think that year bushings are 7/8",, this shackle hole is 1.166", thk/u. gus.
|
Forum: Early V8 (1932-53)
06-30-2019, 02:44 PM
|
Replies: 6
Views: 1,234
rear spring ID?
there are 12 leafs, 2.250" wide, shackle hole is 1.166", grease fitting on center bolt,
Also, Having hard time finding a rubber type shackle bushing for this size 1.166 " hole .thanks gus..
|
Forum: Early V8 (1932-53)
02-19-2014, 12:02 PM
|
Replies: 9
Views: 2,063
Re: steering box?
Thanks Martin ; u understood my lower race ?? , I did protect the threads and with some solid blows the race and shaft came out,and I think the roller bearings are OK ,just a clean up. I just needed...
|
Forum: Early V8 (1932-53)
02-18-2014, 05:13 PM
|
Replies: 9
Views: 2,063
Re: steering box?
Just 2b sure=Obliviously with roller out, I push on steering shaft ,and it pushes out the lower outer race, and if its hard to push out I recken I scrap the bearings ? yes, it has a horn hole in...
|
Forum: Early V8 (1932-53)
02-18-2014, 03:47 PM
|
Replies: 9
Views: 2,063
steering box?
Just got this box in a pile of stuff with my 27T Rod project, how do you remove the steering shaft out of hosing ?, I can see the drag link shaft drops out . there is a barely discernible casting #...
|