Forum: Early V8 (1932-53)
04-14-2024, 05:57 AM
|
Replies: 11
Views: 563
|
Forum: Early V8 (1932-53)
02-11-2024, 06:24 AM
|
Replies: 21
Views: 2,246
Re: Third Gen Automotive
I’ve never had any issues 35fordtn. Thanks anyway for sharing and keep up the great work!
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
12-10-2023, 05:56 AM
|
Replies: 4
Views: 495
|
Forum: Early V8 (1932-53)
11-19-2023, 06:16 AM
|
Replies: 9
Views: 817
Re: Full floating rod bearings
Search this forum for the thread “Bearing clearance “ by Russcc and look at post number 64.
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
10-12-2023, 05:04 AM
|
Replies: 5
Views: 749
|
Forum: Model A (1928-31)
08-05-2023, 07:36 AM
|
Replies: 9
Views: 1,076
Re: Rear Axle bearing Race
If you go to your profile page and look under "statistics" you should be able to pull up all your posts (I think).
|
Forum: Model A (1928-31)
08-05-2023, 05:15 AM
|
Replies: 9
Views: 1,076
Re: Rear Axle bearing Race
On a related note (not being a machinist), how do you go about mounting the housing in a lathe to perform this job?
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
05-30-2023, 05:21 AM
|
Replies: 5
Views: 1,196
Re: What happened to Third Gen Automotive?
Ditto Brent’s comment. I’ve received several orders over the past few months with no issues- the most recent just last week. Am very pleased with Third Gen!
Sent from my iPhone using Tapatalk
|
Forum: Early V8 (1932-53)
05-06-2023, 05:09 AM
|
Replies: 8
Views: 1,050
|
Forum: Early V8 (1932-53)
04-16-2023, 05:39 AM
|
Replies: 17
Views: 1,730
|
Forum: Model A (1928-31)
02-17-2023, 06:15 AM
|
Replies: 28
Views: 3,174
|
Forum: Model A (1928-31)
10-30-2022, 07:22 AM
|
Replies: 17
Views: 2,241
|
Forum: Model A (1928-31)
10-29-2022, 08:45 AM
|
Replies: 17
Views: 2,241
Re: 1931 Standard Roadster Top Bow wood
Here you go. Apologies for the freehand sketch. These are from the uppermost bow in the attached photo. Hope this is what you need!
What part of NB are you from by the way? I was born in Moncton...
|
Forum: Model A (1928-31)
10-28-2022, 05:45 AM
|
Replies: 17
Views: 2,241
Re: 1931 Standard Roadster Top Bow wood
Fundytides: I redid my ‘30 Std top several years ago and kept the original bows. They’re up in the garage loft. Will dig them out this aft, take some pics & measurements and post them for you. Stay...
|
Forum: Early V8 (1932-53)
10-15-2022, 05:20 AM
|
Replies: 16
Views: 1,638
Re: Oil filter canister: Bolt torque?
After leaking a fair bit of oil on initial startup I researched this and came up with 14 lbft. Can’t remember the source but haven’t had a drop pass the cover since!
Sent from my iPhone using...
|
Forum: Early V8 (1932-53)
08-25-2022, 04:02 PM
|
Replies: 6
Views: 712
|
Forum: Early V8 (1932-53)
08-24-2022, 05:31 PM
|
Replies: 6
Views: 712
|
Forum: Early V8 (1932-53)
08-24-2022, 02:15 PM
|
Replies: 6
Views: 712
Need generator advice
Electrical gurus please chime in. I bought a recently rebuilt 2-brush generator and set it up on my engine test stand to check it out (after polarizing per the usual procedure). It didn't appear to...
|
Forum: Early V8 (1932-53)
06-14-2022, 05:36 AM
|
Replies: 20
Views: 2,156
|
Forum: Model A (1928-31)
02-28-2022, 06:18 AM
|
Replies: 11
Views: 1,687
|
Forum: Model A (1928-31)
12-19-2021, 06:18 AM
|
Replies: 4
Views: 1,145
|
Forum: Early V8 (1932-53)
11-06-2021, 03:56 PM
|
Replies: 2
Views: 760
|
Forum: Early V8 (1932-53)
10-25-2021, 03:36 PM
|
Replies: 9
Views: 1,578
Re: Canadian GL4 140 gear oil
Have you tried Crappy Tire? ;-)
They say this TDH stuff complies with API GL-4:
https://www.canadiantire.ca/en/pdp/motomaster-tdh-fluid-5-l-0280215p.html
I'm using it in my '48 Ford 3-spd...
|
Forum: Early V8 (1932-53)
10-14-2021, 08:07 AM
|
Replies: 15
Views: 1,309
Re: 1953 f100
I'm with Tubman on this. Evaporust/Rust-911 worked great on my '39 block. As Tinker points out, probing the water passages to loosen & flush out the crap is also key.
|
Forum: Model A (1928-31)
05-10-2021, 10:31 AM
|
Replies: 34
Views: 5,524
|