Forum: Model A (1928-31)
02-07-2019, 02:41 PM
|
Replies: 8
Views: 2,098
Re: Clutch travel
Check the clutch release arm for a crack. A crack may not be apparent with the clutch engaged, but will open right up when the clutch is depressed.
Jim
|
Forum: Model A (1928-31)
08-04-2018, 11:02 AM
|
Replies: 13
Views: 3,023
Re: 1929 model a back fire
It may be a dirt particle or a small flake of rust that has made its way through the fuel bowl and is partially blocking the bottom of the main jet causing the engine to run lean.
|
Forum: Model A (1928-31)
07-13-2017, 06:05 AM
|
Replies: 13
Views: 2,320
Re: modern points and condensor
NAPA/Echlin has 2 points styles available; CS751 - solid fixed contact and CS755 - vented fixed contact. The condenser is FA82.
|
Forum: Model A (1928-31)
05-31-2017, 11:53 AM
|
Replies: 32
Views: 9,343
|
Forum: Model A (1928-31)
08-25-2014, 07:24 PM
|
Replies: 9
Views: 2,286
Re: powder coating in Maine, NH or MA
I second Joe K's recommendation above. Powder Coating Alternatives did 5 wheels for me back in 2009. Sand blast, undercoated each with a 25% zinc rich powder coat and finished them in gloss black for...
|
Forum: Model-A
11-05-2013, 09:14 AM
|
Replies: 1
Views: 763
|
Forum: Model A (1928-31)
02-06-2013, 05:56 PM
|
Replies: 28
Views: 5,385
Re: turn signals
Consider using a "brakelighter" by J&L Enterprises (see sticky above). They are unobtrusive and mount inside the rear window with suction cups. They act like a third brake light as well as...
|
Forum: Model A (1928-31)
01-20-2013, 02:26 PM
|
Replies: 21
Views: 6,715
Re: Need a small inspection camera
Talk with your plumber. Mine uses a hand held with a flexible wand. An extension can be added to increase viewing distance. I don't know if it has memory capability to be able to be downloaded to a...
|
Forum: Model-A
11-27-2012, 06:03 PM
|
Replies: 1
Views: 957
|
Forum: Model A (1928-31)
06-01-2012, 06:00 AM
|
Replies: 2
Views: 1,589
|
Forum: Model-A
05-13-2012, 06:54 PM
|
Replies: 5
Views: 1,248
|
Forum: Model A (1928-31)
04-05-2012, 04:59 PM
|
Replies: 13
Views: 1,926
Re: Is this a Model generator
The back plate has post production brush holders, I can't tell from your photo if the end plate is cast iron or aluminum. The wiring can be easily changed to install a Model A type stud terminal with...
|
Forum: Model A (1928-31)
04-01-2012, 07:01 PM
|
Replies: 26
Views: 5,311
|
Forum: Model A (1928-31)
12-13-2011, 05:10 PM
|
Replies: 5
Views: 1,855
Re: Zenith Carburetor djustments
It sounds like an air leak. Check for manifold to block tightness, carb to manifold tightness. Condition of gaskets in both areas. Crack in carb mounting flange / manifold. If you have a vacuum...
|
Forum: Model A (1928-31)
10-20-2011, 04:26 PM
|
Replies: 196
Views: 67,621
|
Forum: Model A (1928-31)
12-15-2010, 10:33 AM
|
Replies: 16
Views: 12,969
Re: Everlasting Turn Signal question
I had this same problem using a Wagner 535 flasher. I uncrimped the can from the base and adjusted the metal leaves inside. Pilot light no longer glows when turn signals are off. Be careful when...
|
Forum: Model A (1928-31)
07-28-2010, 01:34 PM
|
Replies: 9
Views: 2,778
|