Forum: Early V8 (1932-53)
02-26-2020, 06:51 PM
|
Replies: 9
Views: 1,650
|
Forum: Early V8 (1932-53)
02-26-2020, 11:36 AM
|
Replies: 9
Views: 1,650
Re: Distributor identification
I hope this works. I've had trouble getting one photo small enough to post.
If JM 35 has never seen an aftermarket distributor of this vintage, then it has to be Ford which is a good thing. Thanks.
|
Forum: Early V8 (1932-53)
02-25-2020, 03:51 PM
|
Replies: 9
Views: 1,650
Distributor identification
I have a 32-36 distributor that I believe is aftermarket, not ford. I bought it just to practice tearing one down. It has 29017, EE and 14 (underlined) on the outside bottom plate. The edge of the...
|
Forum: Early V8
03-13-2019, 01:44 PM
|
Replies: 0
Views: 798
|
Forum: Early V8 (1932-53)
03-01-2019, 05:23 PM
|
Replies: 7
Views: 1,277
Re: Drum and axle compatibility
There is some possibility front and rear drums are 37 as the motor and trans are 37 (v8 60hp). In 1978 two cars could have been combined to make this one. How do I tell 37 axles from 35 or 36?
|
Forum: Early V8 (1932-53)
03-01-2019, 05:03 PM
|
Replies: 7
Views: 1,277
Re: Drum and axle compatibility
I'd like to run 35 wire wheels. As to the front drums, do you think I could get a machine shop to drill my wide five drums in a 5 x 5.5 pattern and install studs and spacers to support the 35 wire...
|
Forum: Early V8 (1932-53)
03-01-2019, 12:45 PM
|
Replies: 7
Views: 1,277
Drum and axle compatibility
My 35 ford has post 35 "wide five" steel artillery wheels and hubs with mechanical brakes. If I can find 35 open "spider" drums or closed drums with hubs, will these direct fit my axles or if not,...
|
Forum: Early V8 (1932-53)
01-15-2019, 05:36 PM
|
Replies: 6
Views: 1,150
|
Forum: Early V8 (1932-53)
12-23-2018, 02:20 PM
|
Replies: 22
Views: 4,045
Re: Coil and Condenser installation help
Thanks John and Pete for the photos which show me correct installation of the original type parts which I now have for my 37 v8 60hp (Pete, your picture is an exact match to my stuff). The car is 6...
|
Forum: Early V8 (1932-53)
12-18-2018, 03:26 PM
|
Replies: 22
Views: 4,045
Coil and Condenser installation help
All I want for xmas is a clear photo of a 37 ford engine showing the correct installation and wiring of an original style condenser and a tall type coil. Car is negative ground. Oh yeah, and for the...
|
Forum: Early V8 (1932-53)
12-10-2018, 02:05 PM
|
Replies: 8
Views: 2,579
Mac's Auto Parts
Does anybody have any experience using the "new" 37 ford 6 volt tall type ignition coil (78-12036-A) from Mac's?
|
Forum: Early V8 (1932-53)
12-03-2018, 06:51 PM
|
Replies: 30
Views: 4,562
|
Forum: Early V8 (1932-53)
12-03-2018, 06:43 PM
|
Replies: 30
Views: 4,562
|
Forum: Early V8 (1932-53)
12-03-2018, 06:41 PM
|
Replies: 30
Views: 4,562
Re: Value of ford v8 60 hp drive train
Car was built in 1978 (apparently from what someone had sitting around) to raffle off at an AACA Antique Car Show in Jekyll Island, Georgia. The car show brochure described it as "attractively...
|
Forum: Early V8 (1932-53)
12-03-2018, 11:22 AM
|
Replies: 30
Views: 4,562
Value of ford v8 60 hp drive train
Recently bought a 35 ford slant back with 37 ford 60 hp which runs great after installing stromberg carb from vintage speed. I can either keep and fix up as a restomod or sell drive train and go...
|
Forum: Questions & Suggestions
12-01-2018, 05:15 PM
|
Replies: 1
Views: 1,399
Best way to go
Recently bought a 35 ford slant back at auction. Has a 37 ford v8 60 hp motor which runs great after I installed a Stromberg carb built by Vintage Speed. For resale value, do I sell the drive train...
|