Forum: Early V8 (1932-53)
06-05-2010, 06:42 PM
|
Replies: 4
Views: 1,538
|
Forum: Early V8 (1932-53)
06-05-2010, 06:33 AM
|
Replies: 20
Views: 4,436
|
Forum: Early V8 (1932-53)
06-05-2010, 06:30 AM
|
Replies: 13
Views: 2,214
Re: hoses
Original hoses were necked down to keep thermostats in place.
|
Forum: Early V8 (1932-53)
06-05-2010, 06:12 AM
|
Replies: 21
Views: 4,304
Re: Vapor lock 47 Merc.
First 55 mph is too much for early Fords in hot weather.Replace the gas line tank to flex line.I had a flex line that acted like a check valve.Try a can of starter fluid next time it stalls in hot...
|
Forum: Early V8 (1932-53)
06-05-2010, 05:43 AM
|
Replies: 11
Views: 2,648
Re: Truck steering wheels
39 to 40 9n used a 4 spoke ton and a half truck wheel.Steiner tractor 800 234 3280.The 9n used over 200 car and truck parts.
|
Forum: Early V8 (1932-53)
06-05-2010, 05:28 AM
|
Replies: 50
Views: 31,977
Re: George "Skip" Haney Water pumps
The Model A only overheated when we used it to power a cord wood saw.Lack of foward motion may have done it but a thermostat stopped the overheating.The Ford never overheated when worked in hot...
|
Forum: Model A (1928-31)
06-04-2010, 07:11 PM
|
Replies: 15
Views: 6,711
|
Forum: Model A (1928-31)
06-04-2010, 06:00 AM
|
Replies: 21
Views: 5,306
Re: Hydraulic Brakes?
Never leak,dream on Pete.After rusty brake lines, leaking wheel cylinders are high failure items.
|
Forum: Model A (1928-31)
06-04-2010, 05:33 AM
|
Replies: 8
Views: 3,085
Re: cut out
You still need a cutout with Toms regulator.Diode cut outs make the generator produce a higher voltage to overcome the diodes resistance.Old Ford generators tend to throw solder at 8 volts,your...
|
Forum: Model A (1928-31)
06-04-2010, 05:25 AM
|
Replies: 22
Views: 5,321
|
Forum: Model A (1928-31)
06-04-2010, 05:22 AM
|
Replies: 8
Views: 2,181
Re: Cam nut removal
I have a large open end wrench with an offset head thatwas made for removing the cam nut.Get the tool and avoid breaking parts.
|
Forum: Early V8 (1932-53)
06-04-2010, 05:11 AM
|
Replies: 14
Views: 2,680
|
Forum: Early V8 (1932-53)
06-04-2010, 05:01 AM
|
Replies: 28
Views: 9,976
|
Forum: Early V8 (1932-53)
06-04-2010, 04:47 AM
|
Replies: 2
Views: 1,270
Re: 53 Mainline brake parts ???
Try Rock Auto for shoes and small parts.The 53 ford had good brakes,I would stay with stock.Many other cars used Bendix brakes, try GM dealers.
|
Forum: Early V8 (1932-53)
06-04-2010, 04:34 AM
|
Replies: 15
Views: 2,789
Re: 1918 cheby V8
Roach is afraid that we will find out there are other makes of cars besides Ford.
|
Forum: Early V8 (1932-53)
06-03-2010, 06:48 PM
|
Replies: 10
Views: 2,337
|
Forum: Early V8 (1932-53)
06-03-2010, 06:31 PM
|
Replies: 7
Views: 2,133
|
Forum: Early V8 (1932-53)
06-03-2010, 06:24 PM
|
Replies: 12
Views: 2,136
|
Forum: Early V8 (1932-53)
06-03-2010, 06:13 PM
|
Replies: 8
Views: 2,173
|
Forum: Early V8 (1932-53)
06-03-2010, 06:09 PM
|
Replies: 24
Views: 14,330
Re: Ignition Resistor
No such thing as an internally resisted coil.No room inside a coil for a 60 watt 4 inch long resistor.The resistors heat would boil the oil and burst the case.
|
Forum: Early V8 (1932-53)
06-03-2010, 06:01 PM
|
Replies: 6
Views: 1,825
Re: coil impedence
Voltage is running high,have a tune up shop measure the voltage output of the coil.
|
Forum: Model A (1928-31)
06-03-2010, 05:37 AM
|
Replies: 12
Views: 2,372
Re: welded balls..
I have welded for over 50 years and would never weld on steering parts.Steering parts are forgings.They are heat treated.I would magnaflux steering parts and rear axle replacments.Many broken axles...
|
Forum: Early V8 (1932-53)
06-03-2010, 05:16 AM
|
Replies: 11
Views: 2,652
Re: questions about a stromberg 97
I have used the Grose jet and find that it sticks shut and leaks by worse than the old needle and seat.Another trouble maker is the Viton soft tip needle,it sticks shut often.
|
Forum: Model A (1928-31)
06-02-2010, 08:08 PM
|
Replies: 15
Views: 3,534
Re: bending Aries SS muffler without breaking?
I take these problems to a shop that has the proper bending tool.They have made exhaust parts for my tractor for a fraction of new cost.They sell all auto parts so I buy most things from them.
|
Forum: Model A (1928-31)
06-02-2010, 07:58 PM
|
Replies: 72
Views: 19,841
Re: For vapor lock nonbelievers
Tom I used some white plastic tubing on an Indian motorcycle that had trouble in hot weather usually a stop lights.That was the cure.Years of troubleshooting in mechanics and electronics have taught...
|