Forum: Early V8 (1932-53)
07-21-2019, 12:22 PM
|
Replies: 5
Views: 1,389
Re: 41 ford ignition switch assy.
So the long one is for a Mercury, do you know what years? I have two of these if someone is looking. the appear to be new. Both tested ok. The bottom left photo is what is in my 41, I have a couple...
|
Forum: Early V8 (1932-53)
07-19-2019, 07:04 PM
|
Replies: 5
Views: 1,389
|
Forum: Early V8 (1932-53)
07-19-2019, 03:02 PM
|
Replies: 5
Views: 1,389
41 ford ignition switch assy.
Hi folks, I need help identifying these ignition switches. One actually fits my 41 but the other I am at a loss to identify. Any help is appreciated. 402085
402086.
|
Forum: Early V8 (1932-53)
06-05-2019, 08:33 PM
|
Replies: 18
Views: 4,133
Re: Alternator wiring
Yes, I did start another thread, sorry about that it has been a while since I was on this site. thank you for both of your responses. Would you use a three wire or perhaps an alternator from summit...
|
Forum: Early V8 (1932-53)
06-05-2019, 04:22 PM
|
Replies: 1
Views: 1,030
12 volt Alt wiring to original loom.
I have not been on here in a number of months and I have looked for my specific question but do not see it.
So here goes, I am installing a 12 volt alt on my 41 Ford flathead. The alt shares a...
|
Forum: Early V8 (1932-53)
06-05-2019, 03:50 PM
|
Replies: 18
Views: 4,133
Re: Alternator wiring
Ok, folks, I am putting a 12v alt on my 41 flatty, it is running electric fans and vintage air, didn't the original generator feed to the voltage regulator and then through the gauge to the starter...
|
Forum: Early V8 (1932-53)
10-03-2015, 11:59 AM
|
Replies: 13
Views: 3,298
|
Forum: Early V8 (1932-53)
10-02-2015, 07:42 PM
|
Replies: 13
Views: 3,298
Re: Flathead engine stand adapter
I see the reference stumpys fab works. I have e-mail a number of times to the address listed on the web site. I have gotten no response. Any one know if he is still in bus and how to maybe call or...
|
Forum: Early V8 (1932-53)
08-05-2011, 06:35 PM
|
Replies: 4
Views: 1,226
41 Bumpers
Can any one tell me if there are more than one bumper style for the 41 car. Were there any smooth, rounded bumpers or were they all the "step" type. Kind of scolloped looking from the end.
|
Forum: Early V8 (1932-53)
08-05-2011, 06:24 PM
|
Replies: 25
Views: 4,354
|
Forum: Early V8 (1932-53)
08-04-2011, 08:58 PM
|
Replies: 25
Views: 4,354
Re: 41 flatty, miserable, spark, stops running.
OK, if I remember any thing from my learnin in the Navy, a resistor only works when it is loaded (attached to the coil). But the coil only loads when the points are closed. therefore completing the...
|
Forum: Early V8 (1932-53)
08-03-2011, 10:03 AM
|
Replies: 25
Views: 4,354
Re: 41 flatty, miserable, spark, stops running.
OK, how much voltage should the coil lead be getting. Mine shows full battery voltage but fluctuates as the engine is rotated. I understand the purpose of the points is to interuprt th power to the...
|
Forum: Early V8 (1932-53)
08-02-2011, 05:20 PM
|
Replies: 25
Views: 4,354
|
Forum: Early V8 (1932-53)
08-02-2011, 05:03 PM
|
Replies: 25
Views: 4,354
41 flatty, miserable, spark, stops running.
I'm new here so give a little time to get up to speed. I recently purchased a 41 Tudor Sedan, it has suprised me at every turn. Can of worms type things.
Any way, I have (had) the engine...
|