Forum: Model A (1928-31)
04-17-2024, 10:58 AM
|
Replies: 44
Views: 9,436
Re: Aries Stainless Steel Muffler
The issues mentioned about the Aries Stainless Steel muffler were posted about 10 years ago. Since then we have taken steps to solve this issue of the the tail pipe breaking apart from the muffler. ...
|
Forum: Model A (1928-31)
04-20-2023, 03:11 PM
|
Replies: 44
Views: 9,436
|
Forum: Model A (1928-31)
04-20-2023, 03:02 PM
|
Replies: 44
Views: 9,436
Re: Aries Stainless Steel Muffler
They only break because they are not mounted properly. The rear clamp has to sufficiently loose to allow for expansion and contraction. Not rattly loose, but sufficient to move if it has to. My...
|
Forum: Model A (1928-31)
04-20-2023, 02:57 PM
|
Replies: 44
Views: 9,436
Re: Aries Stainless Steel Muffler
You should have been using one of our insulated tail pipe clamps. The stainless steel mufflers expand quite a bit more than the steel ones. If you use a standard tail pipe clamp, it will not allow...
|
Forum: Model A (1928-31)
04-30-2021, 09:46 AM
|
Replies: 10
Views: 2,726
Re: Parts for a rebuilder
I am interested in your parts, I have a Model A Ford business here in Medford, OR
please call Joe Davis 650-279-6609 Thanks
|
Forum: Model A (1928-31)
01-05-2017, 12:31 AM
|
Replies: 16
Views: 3,807
|
Forum: Model-A
05-01-2014, 07:25 AM
|
Replies: 0
Views: 806
|
Forum: Model-A
06-11-2013, 12:18 PM
|
Replies: 0
Views: 732
For 30-31 Tudor Sedan
Sheet metal panels in rear that hold window regulators and bolt to body. Need two, right and left. These are under rear windows. Call Joe Davis 650-948-6424 or email [email protected]
|
Forum: Model A (1928-31)
04-07-2012, 10:10 AM
|
Replies: 44
Views: 9,436
Re: Aries Stainless Steel Muffler
very important: Both steel and stainless mufflers must have room to move, there is a great deal of thermal expansion. Failure to allow the tail pipe to move through the clamp will result in cracking...
|
Forum: Model A (1928-31)
03-20-2012, 12:50 PM
|
Replies: 2
Views: 1,006
1929 Cabriolet
78369We need the rubber inserts for the rectagular plates that go on the bottom of the Middle vertical bow. Does any body know who might make these? Also need the body plates that these bump against...
|
Forum: Model-T
01-24-2012, 10:06 AM
|
Replies: 0
Views: 1,445
Joe Davis
need turtle deck and lid for 1920 to 1922 Roadster. contact Joe Davis 650-948-6424
|
Forum: Early V8
10-11-2011, 02:26 PM
|
Replies: 0
Views: 1,148
Joe Davis
Needed for 1939 Convertible Coupe, rear step plates and brackets. P/N 91A 7646202 Upper Bracket, upper Pad 91A 7646206. Lower Bracket: 91A7646204, lower pad 91A 7646208. Contact Joe Davis...
|
Forum: Model-T
07-10-2011, 06:05 PM
|
Replies: 0
Views: 1,054
|
Forum: Model-T
07-10-2011, 05:05 PM
|
Replies: 0
Views: 1,006
|
Forum: Model-A
11-28-2010, 11:02 AM
|
Replies: 1
Views: 1,046
|
Forum: Model-A
11-28-2010, 11:00 AM
|
Replies: 0
Views: 1,429
|
Forum: Model-A
10-02-2010, 02:56 PM
|
Replies: 0
Views: 930
|
Forum: Model-A
10-02-2010, 02:50 PM
|
Replies: 0
Views: 875
|
Forum: Early V8
08-02-2010, 09:06 AM
|
Replies: 0
Views: 1,205
Wanted: 1941 Wheel
Need one more wheel for 1941, this is a disk type wheel, similiar to later wheels but the width at the outside is only 5.25", a little narrower than 46 to 48 wheels, but similiar otherwise. ...
|
Forum: Early V8
07-21-2010, 09:34 PM
|
Replies: 2
Views: 1,117
|