Forum: Model-A
06-14-2023, 06:32 PM
|
|
Replies: 0
Views: 500
Model A Ford library for sale
I've sold my Model A and now would like to sell the books. I have all three of the Les Andrews books, the Rex Reheis A and B carb restoration book, a xerox of rear axle restoration, McCree book on...
|
|
Forum: Model-A
04-06-2023, 08:31 AM
|
|
Replies: 0
Views: 397
1930 Tudor with Ron Kelly engine
Ford 1930 Model A Tudor. This one is a driver. Older restoration but shows nice. Henry body, nice paint and chrome, good upholstery but shows some wear. Total engine rebuild by Ron Kelly with C/B...
|
|
Forum: Model-A
03-25-2023, 07:18 AM
|
|
Replies: 0
Views: 501
|
|
Forum: Model-A
03-16-2017, 01:30 PM
|
|
Replies: 1
Views: 1,312
|
|
Forum: Model-A
03-14-2017, 05:21 PM
|
|
Replies: 1
Views: 1,312
Wanted Flywheel Housing
I need a flywheel housing for my engine that is being rebuilt as I type. I have three cracked ones and would like to find a good one, but I understand (by experience) that this is hard to do. Any...
|
|
Forum: Model A (1928-31)
02-02-2017, 09:32 AM
|
|
Replies: 73
Views: 11,794
|
|
Forum: Model A (1928-31)
02-01-2017, 08:38 PM
|
|
Replies: 73
Views: 11,794
Re: Getting ready to swap engines
Mitch; What do you mean by "slanted spring retainers"? I looked at the picture and can't see it. Thanks.
A question while on the subject; I'm refreshing my spare engine and the pressure plate...
|
|
Forum: Model A (1928-31)
08-03-2016, 07:56 PM
|
|
Replies: 16
Views: 3,683
|
|
Forum: Model A (1928-31)
08-03-2016, 04:57 PM
|
|
Replies: 16
Views: 3,683
Re: Aftermarket U-Joint Problem?
I dropped the rear end and took the U-Joint cover off and yep, it was the Snyder repo U Joint rubbing. The cover had gouges in it from the little action it got rolling back and forth in the shop. ...
|
|
Forum: Model A (1928-31)
08-03-2016, 02:10 PM
|
|
Replies: 16
Views: 3,683
Re: Aftermarket U-Joint Problem?
Thanks for all the responses; I'm having a bit of trouble posting a reply (new to site). I did take great care installing the U Joint washer with nub and did confirm that the tower forks are in...
|
|
Forum: Model A (1928-31)
08-01-2016, 06:39 AM
|
|
Replies: 16
Views: 3,683
Aftermarket U-Joint Problem?
Newbie to the Ford Barn and looking for some help. I just had my engine rebuilt from a reputable builder and replaced the riveted u-joint with a Snyder repo before installation. I put on the...
|
|
Forum: Model A (1928-31)
09-12-2015, 05:08 PM
|
|
Replies: 75
Views: 19,209
Re: Milling a Snyder's head
Most likely, the casting had not stabilized before it was finish milled for sale. Did you ever buy a set of rotors, only to find they "warped" a few months later? Same thing.
|
|
Forum: Model A (1928-31)
09-12-2015, 09:31 AM
|
|
Replies: 75
Views: 19,209
|
|
Forum: Model A (1928-31)
09-12-2015, 07:48 AM
|
|
Replies: 75
Views: 19,209
Re: Milling a Snyder's head
Hello, I'm a first-timer to the Ford Barn. I have a question and this seems to be the thread to put it in; Les Andrews said in Vol II that the Snyder 5.5 head can be milled down ".080 to .125 by a...
|
