Forum: Early V8 (1932-53)
07-30-2025, 09:11 PM
|
|
Replies: 14
Views: 952
Re: 34 Ford coupe converting rumble seat to trunk
I have done mine, this is what I did! , (AS said) ,The stamping for the trunk hinges are at the top (inside ) ,The stamping for the rumble seat hinges are at the bottom (sides) , the handle moves to...
|
|
Forum: Early V8 (1932-53)
07-16-2025, 06:12 PM
|
|
Replies: 6
Views: 2,283
|
|
Forum: Early V8 (1932-53)
07-14-2025, 11:00 PM
|
|
Replies: 6
Views: 2,283
|
|
Forum: Early V8 (1932-53)
07-13-2025, 10:54 PM
|
|
Replies: 6
Views: 2,283
1935/36 pick up
Fitting a 35 grill on a 36 what needs to be changed ,Hood ,Radiator .?? Has any one done this .Thanks ,
|
|
Forum: Early V8 (1932-53)
07-13-2025, 07:54 PM
|
|
Replies: 31
Views: 6,708
Re: Q: 34 Ford Coupe RHD rear window regulator
Some times as far as the wood goes canadian products followed the usa version , eg the RHD Canadian seat frame for the 34 Roadster has the reinforcing strut 3/4 towards the left side not supporting...
|
|
Forum: Early V8 (1932-53)
06-20-2025, 12:33 AM
|
|
Replies: 10
Views: 1,465
Re: Wiring: 1933 Ford conduit tube.
I would think about running those two on the out side of tube or under with two clips as future maintenance on the distributor its better to have the tube and terminals caps removable ,
|
|
Forum: Early V8 (1932-53)
06-19-2025, 10:48 PM
|
|
Replies: 27
Views: 3,819
Re: '36 floor pans?
Kube I am trying to post a picture and pointers of how you can make floor pans that you can do your self , They don't down load . I will try on test thred ,Ted
|
|
Forum: Early V8 (1932-53)
06-19-2025, 07:47 PM
|
|
Replies: 27
Views: 3,819
|
|
Forum: Early V8 (1932-53)
06-18-2025, 10:54 PM
|
|
Replies: 27
Views: 3,819
|
|
Forum: Early V8 (1932-53)
06-12-2025, 11:16 PM
|
|
Replies: 22
Views: 3,053
Re: Ted’s brake floaters
If your drums and shoes are worn you can get this issue ,pack up the slots in the top end of the shoe adjuster links with a rivet or a one inch length of 4 " nail ,bend the end to right angle , Or...
|
|
Forum: Early V8 (1932-53)
05-26-2025, 09:15 PM
|
|
Replies: 83
Views: 12,127
|
|
Forum: Early V8 (1932-53)
05-26-2025, 08:51 PM
|
|
Replies: 83
Views: 12,127
|
|
Forum: Early V8 (1932-53)
05-26-2025, 04:37 PM
|
|
Replies: 83
Views: 12,127
|
|
Forum: Early V8 (1932-53)
05-07-2025, 05:27 PM
|
|
Replies: 9
Views: 1,554
Re: Head lining kit
Try Read and twyman in Auckland ,They have large sheets of chicken foot textured black card https://www.retwine.co.nz/
|
|
Forum: Early V8 (1932-53)
04-22-2025, 06:36 PM
|
|
Replies: 10
Views: 1,399
Re: 1934-1935-1936 Ford Spare Wheel Covers.
A bit of topic lf your interested !I body worked my Chrome trim for my 35 in the day by making a T shaped bit of flat steel welded to a 1/4 round rod . I shaped the flat bit to slide in with a...
|
|
Forum: Early V8 (1932-53)
04-10-2025, 09:22 PM
|
|
Replies: 3
Views: 2,954
|
|
Forum: Early V8 (1932-53)
04-01-2025, 09:50 PM
|
|
Replies: 20
Views: 3,503
|
|
Forum: Early V8 (1932-53)
03-30-2025, 08:10 PM
|
|
Replies: 12
Views: 6,169
|
|
Forum: Early V8 (1932-53)
03-30-2025, 07:13 PM
|
|
Replies: 12
Views: 6,169
|
|
Forum: Early V8 (1932-53)
03-24-2025, 04:37 PM
|
|
Replies: 10
Views: 1,446
Re: Odd grill
Yes we had one just like that Grey my preferred grill .Dad cut it to a pick up we would get it side ways on the gravel coast rd at Tasman sth island ,Smoked like a steam train ,but not short...
|
|
Forum: Early V8 (1932-53)
03-03-2025, 10:22 PM
|
|
Replies: 3
Views: 500
Re: 33 terminal plates
Lawrie ,Run a propane torch around the out side ,tap the top of the cap with a drift or screwdriver on the edge through the coil hole ,
|
|
Forum: Early V8 (1932-53)
03-03-2025, 09:41 PM
|
|
Replies: 71
Views: 6,725
Re: Chasing same issues again any ideas? ‘34
I do work for a Museum of 200 x cars some of them have been dormant for 20 years or so and Towing them works for a 1st start up ,it can pump up the rings with oil increasing compression .We did a...
|
|
Forum: Early V8 (1932-53)
03-03-2025, 03:56 PM
|
|
Replies: 71
Views: 6,725
|
|
Forum: Early V8 (1932-53)
03-02-2025, 05:20 PM
|
|
Replies: 63
Views: 4,655
Re: 1933 Ford Deluxe V8 Phaeton in France
The measurements between the cowl and the rear door shuts on the Phation are the the same as usa ones ,the front doors are also the same in length .The rear doors are a 1" shorter in length, the...
|
|
Forum: Early V8 (1932-53)
02-28-2025, 03:41 PM
|
|
Replies: 63
Views: 4,655
|
