Forum: Model A (1928-31)
Yesterday, 04:58 PM
|
Replies: 7
Views: 163
Re: Front Hub Stuck to Brakes
You might try mounting the tire with a couple of lug nuts
to give you some leverage and rotate it as you push or pull the wheel.
|
Forum: Model A (1928-31)
Yesterday, 04:47 PM
|
Replies: 1
Views: 83
|
Forum: Model A (1928-31)
Yesterday, 09:35 AM
|
Replies: 10
Views: 378
Re: A A transmission HELP!
The trans is from a Model AA but the rear bearing retainer looks
like 1932-39. The parts picture is from Van Pelt's site http://www.vanpeltsales.com/ . The same picture is in the Ford parts books.
|
Forum: Model A (1928-31)
06-11-2024, 09:33 PM
|
Replies: 10
Views: 378
Re: A A transmission HELP!
The keeper #7155 in the picture must be missing. I would take the cover off the trans and see what it looks like inside. The
cluster gear has probably dropped down and is not engaged
with the...
|
Forum: Model A (1928-31)
06-11-2024, 03:24 PM
|
Replies: 10
Views: 378
Re: A A transmission HELP!
If you are asking about this it looks line the counter shaft coming out of the transmission. Need a picture showing more of the transmission to tell for sure.
|
Forum: Model A (1928-31)
06-08-2024, 05:02 PM
|
Replies: 5
Views: 303
|
Forum: Model A (1928-31)
06-08-2024, 01:48 PM
|
Replies: 5
Views: 191
Re: Gear Drive Starter Question
This is from Terry Burtz new engine guide.
"The new flywheel does not come with a ring gear installed because the beveled teeth on the ring gear need to be at the rear if using a Model A starter,...
|
Forum: Model A (1928-31)
06-07-2024, 01:42 PM
|
Replies: 31
Views: 3,178
Re: Distributor won't drop in fully...
The short answer is probably not as it's hard to get to the lower shaft because of the spring that hold the oil pump drive gear in place. I had one that was really stuck and I had to make a collet...
|
Forum: Model A (1928-31)
06-06-2024, 08:10 PM
|
Replies: 5
Views: 303
|
Forum: Early V8 (1932-53)
06-06-2024, 05:25 PM
|
Replies: 41
Views: 1,672
Re: Front Axle 1939 Ford pickup
The lock pin for the king pin is the same 1928-48 and I have the blue prints for the Model A axle and the hole is reamed .561-.563,
it's not tapered.
|
Forum: Early V8 (1932-53)
06-06-2024, 11:16 AM
|
Replies: 41
Views: 1,672
|
Forum: Early V8 (1932-53)
06-05-2024, 10:03 AM
|
Replies: 14
Views: 386
|
Forum: Early V8 (1932-53)
06-04-2024, 03:31 PM
|
Replies: 8
Views: 394
|
Forum: Model A (1928-31)
06-04-2024, 12:41 PM
|
Replies: 1
Views: 143
Re: Connecting the light switch
The notch in the contact plate and the lower part of the switch
go in a tab in the upper part of the switch. You can see the tab in the picture right above the bolt.
|
Forum: Model A (1928-31)
06-04-2024, 12:11 PM
|
Replies: 9
Views: 509
|
Forum: Model A (1928-31)
06-01-2024, 09:04 PM
|
Replies: 3
Views: 395
|
Forum: Model A (1928-31)
06-01-2024, 02:16 PM
|
Replies: 24
Views: 1,098
|
Forum: Model A (1928-31)
05-31-2024, 09:38 PM
|
Replies: 24
Views: 1,098
|
Forum: Model A (1928-31)
05-29-2024, 10:06 AM
|
Replies: 27
Views: 1,708
Re: Move A By Yourself
Here you go, ain't cheap. https://duckduckgo.com/?t=h_&q=light+airplane+tug&iax=shopping&ia=shopping
|
Forum: Early V8 (1932-53)
05-27-2024, 02:42 PM
|
Replies: 41
Views: 1,672
|
Forum: Model A (1928-31)
05-25-2024, 02:29 PM
|
Replies: 6
Views: 421
|
Forum: Early V8 (1932-53)
05-25-2024, 10:09 AM
|
Replies: 8
Views: 574
Re: Brake stud repair tool
Here is a link to Vince's site showing how to swage the stud.
https://www.fordgarage.com/pages/swaging.htm
|
Forum: Model A (1928-31)
05-24-2024, 09:04 PM
|
Replies: 14
Views: 491
|
Forum: Model A (1928-31)
05-24-2024, 11:00 AM
|
Replies: 6
Views: 521
|
Forum: Early V8 (1932-53)
05-23-2024, 08:15 PM
|
Replies: 12
Views: 373
Re: Stake bed gate hinges
Could you modify these to make what you need?
https://www.buyersproducts.com/product/straight-stake-rack-connector-set-753
|