Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.09 seconds. Search: Posts Made By: katy
Forum: Model A (1928-31) Yesterday, 09:16 AM
Replies: 7
Views: 227
Posted By katy
Re: 1929 Model A With 12v Conversion

Generator or alternator?
Forum: Model A (1928-31) Yesterday, 09:05 AM
Replies: 23
Views: 738
Posted By katy
Re: Watching YouTube videos pertaining to Model-A repair or restoration...

Just set the timing the Ford way, simple and easy, no special tool(s) needed. Been doing it that way for well over 60 years and never had a problem. No need to waste time watching videos.
Forum: Model A (1928-31) Yesterday, 08:54 AM
Replies: 13
Views: 382
Posted By katy
Re: Too much gear lube

When and by whom did the last check?
Forum: Model A (1928-31) 06-12-2024, 05:50 PM
Replies: 7
Views: 366
Posted By katy
Re: Tires

A 550 tire will add approximately 1" to the OD.
Forum: Model A (1928-31) 06-12-2024, 05:44 PM
Replies: 11
Views: 335
Posted By katy
Re: Front Hub Stuck to Brakes

You might try a hub puller, they're not made for this purpose, but might work.
If you try one, rotate the assembly while pulling.
Forum: Model A (1928-31) 06-11-2024, 09:07 AM
Replies: 7
Views: 372
Posted By katy
Re: Replacing hydraulic brake lines

Are you talking about the steel lines? Or the flexible lines? Or all?
Forum: Model A (1928-31) 06-09-2024, 08:33 PM
Replies: 27
Views: 1,749
Posted By katy
Re: Sealed beams

[QUOTE=David in San Antonio;2305241]
The other type, manufactured by LogoLite and available from the usual distributors, is a complete, self-contained optical system.[QUOTE]

If they don't use the...
Forum: Model A (1928-31) 06-08-2024, 08:44 PM
Replies: 7
Views: 462
Posted By katy
Re: Wobbly dist—hard to disgnose/fix?

If the whole distributor is wobbling, I would suspect that either the distributor body or the opening in the head are worn, or both.
Forum: Model A (1928-31) 06-08-2024, 08:35 PM
Replies: 10
Views: 526
Posted By katy
Re: Tight Fit for Inner Wheel Bearing

That inner bearing should be a slip fit, not locked on.
Forum: Model A (1928-31) 06-08-2024, 08:26 PM
Replies: 27
Views: 1,749
Posted By katy
Re: Sealed beams

Does anyone make 6 volt LED sealed beams?
Forum: Model A (1928-31) 06-08-2024, 08:11 PM
Replies: 13
Views: 501
Posted By katy
Re: Next step?....

Before installing rings in an engine, always, always, measure and adjust (if needed) the end gap on ALL rings before installing them.
When measuring ring end gap, if it's too small one just files...
Forum: Model A (1928-31) 06-07-2024, 09:16 AM
Replies: 10
Views: 526
Posted By katy
Re: Tight Fit for Inner Wheel Bearing

That bearing should be a slip fit, not too loose and not too tight.
Forum: Model A (1928-31) 06-06-2024, 09:18 AM
Replies: 18
Views: 662
Posted By katy
Re: Polarity tester

Here ya go: https://testbook.com/mechanical-engineering/electronic-ignition-system#:~:text=An%20electronic%20ignition%20system%20operates,fuel%20economy%20and%20reduced%20emissions.
Forum: Model A (1928-31) 06-05-2024, 09:56 AM
Replies: 9
Views: 630
Posted By katy
Re: TRB Overdrive?

Possibly made by TRB Automotive for .................
Need more info, pictures would help.
Forum: Model A (1928-31) 06-04-2024, 09:50 AM
Replies: 17
Views: 730
Posted By katy
Re: Adjusting timing

One of these helps,
Forum: Model A (1928-31) 06-03-2024, 05:18 PM
Replies: 24
Views: 1,121
Posted By katy
Re: Different length rear axle shaft threads on either side?

If the axles "spin" inside the hub tapers one won't go very far.
Forum: Model A (1928-31) 06-02-2024, 10:27 AM
Replies: 24
Views: 1,121
Posted By katy
Re: Different length rear axle shaft threads on either side?

Steel washer should be special hardened washer, not your garden variety mild steel one.
Forum: Model A (1928-31) 05-27-2024, 10:09 AM
Replies: 17
Views: 2,213
Posted By katy
Re: powermaster 6 volt alternator install 1928 model a

A segmented (aka link) belt should work. You can adjust the length.
Forum: Model A (1928-31) 05-27-2024, 10:07 AM
Replies: 12
Views: 1,206
Posted By katy
Re: Stupid question of the day. (maybe the year)

Use some heavy grease to hold the gasket to the block.
Forum: Model A (1928-31) 05-27-2024, 09:26 AM
Replies: 23
Views: 1,502
Posted By katy
Re: Electric Fuel Shut off

That's why the make/sell adaptors.
Forum: Model A (1928-31) 05-26-2024, 09:54 AM
Replies: 28
Views: 1,790
Posted By katy
Re: A perplexing oiling problem - A new one to me!

Check the oil pump and passages. Did you do anything with the pump?
Forum: Model A (1928-31) 05-26-2024, 09:33 AM
Replies: 23
Views: 1,502
Posted By katy
Re: Electric Fuel Shut off

If I was going to use the solenoid shut off valve I would put it under the dash, not in the engine compartment.
Forum: Model A (1928-31) 05-25-2024, 11:02 AM
Replies: 4
Views: 414
Posted By katy
Re: 1931 Roadster

Which do you have? The roadster or the pickup?
Forum: Model A (1928-31) 05-25-2024, 10:39 AM
Replies: 6
Views: 524
Posted By katy
Re: Ford Tool Identification

Model T tools generally start with a T prefix. I assume Model A are the same but don't know for sure.
Forum: Model A (1928-31) 05-25-2024, 10:37 AM
Replies: 22
Views: 1,218
Posted By katy
Re: Another carb needs repair

Please report back and let the community know how it worked out. Tnks
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:41 AM.