Forum: Model A (1928-31)
Today, 04:29 AM
|
Replies: 2
Views: 83
Re: Cast fuel bowl leaking- round two
Thanks, Dave. I'm fairly certain it's coming from there. I've done the paper towel dabbing trick and it always underneath the screw. It's small enough that it will "pool" up for a bit on the flat...
|
Forum: Model A (1928-31)
Yesterday, 08:49 PM
|
Replies: 2
Views: 83
Cast fuel bowl leaking- round two
OK, so I posted a while back about my weeping/leaking cast fuel bowl for a '28 roadster. I recent took it off, ground the internal vertical seat that the drain needle seats in with a stone, found a...
|
Forum: Early V8 (1932-53)
Yesterday, 06:36 PM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
Yesterday, 06:36 PM
|
Replies: 26
Views: 686
Re: Pictures after head swap (hot rod content)
Thank you, GB. I'll post some full car shot in a bit. Warning, it's an old hot rod and may have the worst fuel efficiency of any car I've owned. I've calculate 12-14 mph. It could be because...
|
Forum: Early V8 (1932-53)
Yesterday, 06:34 PM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
Yesterday, 11:07 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
Yesterday, 09:34 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 12:13 PM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 09:06 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 08:54 AM
|
Replies: 26
Views: 686
Re: Pictures after head swap (hot rod content)
Unfortunately, I did. The two casting "nubs" on the lower section of fins on each head weeped. I finally got them to stop with 2 doses of liquid glass, but it was still bugging me that it was...
|
Forum: Early V8 (1932-53)
05-27-2024, 08:51 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 08:18 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 08:18 AM
|
Replies: 26
Views: 686
|
Forum: Early V8 (1932-53)
05-27-2024, 07:20 AM
|
Replies: 26
Views: 686
Pictures after head swap (hot rod content)
Finished swapping the Cyclone heads to new Edelbrocks. Hard to tell, but I polished the sides and fin tops. I guess I'll need to do the intake next winter, haha.
Happy to find the NOS...
|
Forum: Early V8 (1932-53)
05-26-2024, 04:39 PM
|
Replies: 13
Views: 535
|
Forum: Early V8 (1932-53)
05-26-2024, 08:19 AM
|
Replies: 13
Views: 535
|
Forum: Early V8 (1932-53)
05-25-2024, 08:43 PM
|
Replies: 12
Views: 493
|
Forum: Early V8 (1932-53)
05-25-2024, 09:08 AM
|
Replies: 13
Views: 535
|
Forum: Early V8 (1932-53)
05-25-2024, 07:04 AM
|
Replies: 13
Views: 535
|
Forum: Early V8 (1932-53)
05-24-2024, 09:25 AM
|
Replies: 10
Views: 415
Re: Head bolt/stud sealant
I've also ordered some Leak Lock. Thanks for the tip, Robert.
I've used ARP in the past. I'd assume they just repackage someone else's product. This go around I'm using Hercules thread...
|
Forum: Early V8 (1932-53)
05-24-2024, 07:52 AM
|
Replies: 21
Views: 1,007
Re: Crane 400 Cam and a AL-1 cam
I'd have think that south of the Mason Dixon line there are a lot of old Crane cams sitting in garages, old shops, etc. I'd love the try one as well.
|
Forum: Early V8 (1932-53)
05-24-2024, 07:28 AM
|
Replies: 12
Views: 528
|
Forum: Early V8 (1932-53)
05-23-2024, 11:01 AM
|
Replies: 3
Views: 289
|
Forum: Early V8 (1932-53)
05-23-2024, 08:43 AM
|
Replies: 31
Views: 1,070
Re: One Head stud too short each bank follow-up
All is well. Hope the same with you. Learned something new. Never seen that Lube Lock product before. I like how it comes in a liquid. Paste products can be quite a mess. Have you used it before?
|
Forum: Early V8 (1932-53)
05-23-2024, 08:32 AM
|
Replies: 31
Views: 1,070
|