Forum: Model A (1928-31)
07-10-2013, 11:57 PM
|
Replies: 44
Views: 9,835
Re: What State is Model A Friendly ???
Sit tight, don't make any moving plans!
There should only be fees involved in your DMV activity. The reason being you are not purchasing or transferring the vehicle. The reason for the cost of...
|
Forum: Model A (1928-31)
06-28-2013, 12:12 AM
|
Replies: 16
Views: 2,877
|
Forum: Model A (1928-31)
06-27-2013, 01:09 PM
|
Replies: 11
Views: 4,604
|
Forum: Model A (1928-31)
06-25-2013, 10:21 PM
|
Replies: 18
Views: 4,022
Re: Where does one find an oil return pipe?
I had the cockeyed cup problem and fixied it bolting the pipe up without gaskets. I then put a propane torch on the tube near each cup and when the solder relaxed I tightened the bolts. This allowed...
|
Forum: Model A (1928-31)
06-23-2013, 06:30 PM
|
Replies: 10
Views: 1,983
Re: No start
From your description, "with the key off I have 6V at both coil terminals and both fastners at the box on the firewall. Nothing at the points.", this is as it should be. There should be six volts all...
|
Forum: Model A (1928-31)
06-23-2013, 12:10 AM
|
Replies: 28
Views: 7,522
Re: Back flushing the radiator
By disconnecting the top and bottom hoses and applying water pressure to the bottom radiator hose neck. The catch is you are fighting gravity, a baffle, etc. You can do the block at the same time...
|
Forum: Model A (1928-31)
06-09-2013, 11:58 PM
|
Replies: 17
Views: 7,535
|
Forum: Model A (1928-31)
06-09-2013, 11:47 PM
|
Replies: 31
Views: 9,636
|
Forum: Model A (1928-31)
06-04-2013, 11:28 PM
|
Replies: 15
Views: 3,097
Re: who's running what
3 7/8 x 4 1/4 Sleeved to Std.
Counterweighted crank
Insert main bearings
One piece rear seal
Insert rod bearings
Fully balanced
1 3/4 Intake 1 9/16 Exhaust valves
Self locking adjustable...
|
Forum: Model A (1928-31)
05-30-2013, 12:14 AM
|
Replies: 17
Views: 3,933
|
Forum: Model A (1928-31)
05-22-2013, 11:25 PM
|
Replies: 14
Views: 2,862
Killer virus
Well here I am, I'm back.
All I did was search for shock info and I wound up at the H.A.M.B. Jalopy Journal. Got an alert about suspicious code and ignored it, twice. Got a Java script warning...
|
Forum: Model A (1928-31)
05-10-2013, 07:41 PM
|
Replies: 25
Views: 7,734
Re: Fordbarn Barn Finds...
My 31 pickup sat in my backyard for thirty years. Fired it up, drove it out, got it registered and turned it into a Woody. My bad! :eek:
|
Forum: Model A (1928-31)
04-29-2013, 11:56 PM
|
Replies: 10
Views: 3,121
Re: Thanks for the Forditude boost
Update! The rearend went fine (I think). The rear brakes were a mess so I did some temp work on them. A cam was frozen so I got that freed up. The adgusting shafts were two different lengths with the...
|
Forum: Model A (1928-31)
04-29-2013, 11:30 PM
|
Replies: 7
Views: 1,922
Re: dirrerential adjustments
Gary,
My first thought is silicon. What you have is the the carrier preload to be concerned with. Keep the banjo gaskets in order and try silicon at the leak areas, which should show on the gaskets....
|
Forum: Model A (1928-31)
04-17-2013, 05:16 PM
|
Replies: 46
Views: 10,899
Re: not enough backpressure?
Whoa, you're finding to many things to guess at. Stop, put the Meineke muffler back on and see if this corrects your problem. If it does then leave it or put the glass pack on and rejet the carb....
|
Forum: Model A (1928-31)
04-17-2013, 12:02 AM
|
Replies: 7
Views: 2,225
|
Forum: Model A (1928-31)
04-16-2013, 11:39 PM
|
Replies: 46
Views: 10,899
Re: not enough backpressure?
I'm with Mike on this one. You have altered the flow properties. An increase in exaust flow will require an increase in intake flow. Run it and read the plugs. I have a glass pack and headers on mine...
|
Forum: Model A (1928-31)
04-14-2013, 10:00 PM
|
Replies: 62
Views: 16,063
|
Forum: Model A (1928-31)
04-12-2013, 09:49 PM
|
Replies: 13
Views: 2,467
|
Forum: Model A (1928-31)
04-11-2013, 06:19 PM
|
Replies: 7
Views: 1,757
|
Forum: Model A (1928-31)
04-09-2013, 10:28 PM
|
Replies: 149
Views: 51,059
Re: Mac's survey
I ordered differential parts from Mac's, bearings, seals, seal tool, gaskets and shims. The seal tool was out of stock and they contacted me whereupon I cancelled that part. At the same time I...
|
Forum: Model A (1928-31)
04-09-2013, 12:01 AM
|
Replies: 4
Views: 1,328
Re: Front Brake Lever Pins
1/4" if I am reading Les Andrews Vol I page 1-32 correctly. Brattons says the same 2013 catalog page 12.
|
Forum: Model A (1928-31)
04-08-2013, 07:48 PM
|
Replies: 11
Views: 2,854
|
Forum: Model A (1928-31)
04-08-2013, 07:40 PM
|
Replies: 112
Views: 27,369
Re: generator or alternator
Fred, Now that you have clarified your statement, i.e. an alternator that looks like a stock generator, I have nothing to contradict. In fact, I wholeheartedly support what you say. I did read post...
|
Forum: Model A (1928-31)
04-08-2013, 12:27 AM
|
Replies: 112
Views: 27,369
Re: generator or alternator
I like your thinking also!! :D Better yet forget the fenders and call it a Speedster, maybe some 16" wheels and tires from a mid 30's Ford from E-bay because who cares about price. Glass... we don't...
|