Forum: Early V8 (1932-53)
06-10-2024, 10:27 AM
|
Replies: 9
Views: 267
Re: 59A Flathead Running Rich, Need Help
Are you using the gaskets for the power valves? They may be leaking. Have you checked float level? It's possible the accelerator pumps are supplying too much fuel. Is the accelerator link in the...
|
Forum: Early V8 (1932-53)
06-10-2024, 06:26 AM
|
Replies: 3
Views: 262
|
Forum: Early V8 (1932-53)
06-09-2024, 06:20 AM
|
Replies: 41
Views: 1,664
Re: Front Axle 1939 Ford pickup
The bolt is in the middle of the spring length and width, it functions to hold all the spring leafs together. It has a Zerk fitting on the bottom of the bolt for spring lubrication. The square head...
|
Forum: Early V8 (1932-53)
06-09-2024, 05:37 AM
|
Replies: 27
Views: 920
|
Forum: Early V8 (1932-53)
06-06-2024, 06:27 AM
|
Replies: 41
Views: 1,664
Re: Front Axle 1939 Ford pickup
The front spring has a square headed bolt in the center (about 3/8" tall head) that fits into a square hole in the front crossmember. This does not allow the spring pack to move left or right,...
|
Forum: Early V8 (1932-53)
06-04-2024, 07:34 AM
|
Replies: 27
Views: 1,432
Re: Anyone have one they can measure?
Below is another photo of the early 35 intake manifold with it's round hole under the fuel pump riser for the internal baffle tube. The baffle tube and the tube off the fuel pump riser are the...
|
Forum: Early V8 (1932-53)
06-04-2024, 07:11 AM
|
Replies: 17
Views: 386
Re: 39 synchronizer question
That is the 81A syncro hub and it should have three steel balls and springs. Mac sells a kit with the balls and springs for the syncro. The transmission has to come apart to install the kit. With...
|
Forum: Early V8 (1932-53)
06-03-2024, 07:00 AM
|
Replies: 27
Views: 1,432
Re: Anyone have one they can measure?
Although the shorter tube at 4-1/2" is the most popular they did come with the longer depending upon the intake manifold. The 35-36 restoration book explains the difference in the intake manifolds...
|
Forum: Early V8 (1932-53)
06-01-2024, 06:36 AM
|
Replies: 9
Views: 521
|
Forum: Early V8 (1932-53)
06-01-2024, 06:15 AM
|
Replies: 15
Views: 668
|
Forum: Early V8 (1932-53)
05-30-2024, 07:08 AM
|
Replies: 9
Views: 629
|
Forum: Early V8 (1932-53)
05-30-2024, 06:18 AM
|
Replies: 14
Views: 432
|
Forum: Early V8 (1932-53)
05-30-2024, 06:16 AM
|
Replies: 2
Views: 192
Re: 1947 Cluster Gear Endplay Opinion
0.010" steel shim stock cut like a washer and place between the case and the front thrust washer, cut the OD so it does not rotate. Appears the case is worn, if the case does not have flat thrust...
|
Forum: Early V8 (1932-53)
05-29-2024, 09:00 AM
|
Replies: 27
Views: 1,432
|
Forum: Early V8 (1932-53)
05-25-2024, 07:25 AM
|
Replies: 3
Views: 200
|
Forum: Early V8 (1932-53)
05-25-2024, 07:08 AM
|
Replies: 9
Views: 324
|
Forum: Early V8 (1932-53)
05-25-2024, 07:01 AM
|
Replies: 8
Views: 345
Re: three brush regulator
Suggest changing the operation of the two rate to be the same as the regular cutout. Just add the diode or you may be able to put the internals of a Fun Projects inside.
|
Forum: Early V8 (1932-53)
05-24-2024, 09:35 AM
|
Replies: 3
Views: 200
|
Forum: Early V8 (1932-53)
05-23-2024, 06:10 AM
|
Replies: 4
Views: 335
|
Forum: Early V8 (1932-53)
05-22-2024, 06:08 AM
|
Replies: 11
Views: 569
Re: 40 gearset in a 46 pu case
If you have a used 81A main shaft and want to use it I suggest pulling out the small locating pin and replacing it with a new pin.
|
Forum: Early V8 (1932-53)
05-19-2024, 06:45 AM
|
Replies: 21
Views: 1,760
Re: 39 Ford deluxe can't remove cam
The pressed on gear does not have a retainer to remove. Suggest drill small holes on the gear where it attaches to the cam to release the broken cam gear.
|
Forum: Early V8 (1932-53)
05-19-2024, 06:38 AM
|
Replies: 12
Views: 561
Re: Crab distributor vacuum line
Use the bigger hole in the mid rear of the manifold for both wiper and distributor vacuum. Your intake manifold looks like 1935 Ford with modifications by someone. The vacuum lines can be made of...
|
Forum: Early V8 (1932-53)
05-17-2024, 09:29 AM
|
Replies: 8
Views: 857
Re: Verify 1934 Ford Accessories, Please
The Ohil-Chex gauge was not a Ford approved accessory but an aftermarket. The dual temperature and fuel gauge was a Ford accessory. The V8 Club restoration book for 33-34 has a full list of...
|
Forum: Early V8 (1932-53)
05-17-2024, 09:12 AM
|
Replies: 7
Views: 487
Re: 33 Fordoor windshield removal
If the hinges are removed and the hand crank opener is removed from the frame the windshield should come off. The inside of the frame is painted black and for the Deluxe the outside is chrome. New...
|
Forum: Early V8 (1932-53)
05-16-2024, 08:46 AM
|
Replies: 11
Views: 1,597
|