Forum: Early V8 (1932-53)
11-15-2015, 08:31 PM
|
Replies: 14
Views: 2,571
Re: Columbia shifting problem
I have mine operating on 12 volt, it it just momentary unless you hold the clutch down to the floor. I use a starter button mounted under the carpet. The button is activated when the pedal is pushed...
|
Forum: Early V8 (1932-53)
11-15-2015, 08:53 AM
|
Replies: 14
Views: 2,571
Re: Columbia shifting problem
Thanks for the Electrical troubleshooting. It has to be grounding out. I have two light's in the switch harness, 1 to monitor power when I engage clutch and one to confirm power to the HI Side. some...
|
Forum: Early V8 (1932-53)
11-14-2015, 10:39 AM
|
Replies: 14
Views: 2,571
Re: Columbia shifting problem
I have a similar problem. John in Temecula Ca. does not have any new or NOS solenoids, He only carries rebuild kit's( 2 gasket and 2 sealing washers). My shift problem is that my solenoid...
|
Forum: Early V8 (1932-53)
11-03-2015, 11:30 AM
|
Replies: 49
Views: 11,238
|
Forum: Early V8 (1932-53)
10-30-2015, 07:30 PM
|
Replies: 49
Views: 11,238
Re: Yet another MACS experience !
Well hell, I ordered a rotor for a 37 ford dist in may and it still hasn't arrived. called three or four time's and got the it back ordered or it coming in any day. The last time it was at the...
|
Forum: Early V8 (1932-53)
10-19-2015, 11:12 AM
|
Replies: 8
Views: 2,475
|
Forum: Early V8 (1932-53)
10-10-2015, 01:33 PM
|
Replies: 8
Views: 2,475
Re: IDing camshaft
Thanks Ron, but the stamping is F5 and T3, I did a little research and found that Weber used the letter F in their number designation, F1 thru F7
|
Forum: Early V8 (1932-53)
10-10-2015, 06:46 AM
|
Replies: 8
Views: 2,475
IDing camshaft
Trying to ID the cam in my 221, It has F5 and T3 stamped in the dist drive, Does anybody have information, Its seem pretty lumpy.
|
Forum: Early V8 (1932-53)
09-11-2015, 11:58 AM
|
Replies: 0
Views: 1,017
columbia solenoid body
Help , anybody have a good elec. shift body for a columbia, mine has a major dent in the low side seal surface. Tried to polish it out with valve lapping compound, no wayno. :(
|
Forum: Early V8 (1932-53)
08-25-2015, 11:28 AM
|
Replies: 26
Views: 6,329
|
Forum: Early V8 (1932-53)
08-25-2015, 07:41 AM
|
Replies: 26
Views: 6,329
Re: Need Distributor Help!
I will trade you mine, 3 bolt mallory for a ford crab. I have the adapter, Will I need the button spacer?
|
Forum: Early V8 (1932-53)
04-11-2015, 06:49 PM
|
Replies: 3
Views: 760
|
Forum: Early V8 (1932-53)
04-11-2015, 03:07 PM
|
Replies: 3
Views: 760
Vac break Vacuum
does the dist vacuum brake work off of ported or straight manifold vacuum
|
Forum: Early V8 (1932-53)
04-11-2015, 08:54 AM
|
Replies: 8
Views: 1,425
Re: early plug wire sets
I will buy new wires, also I will use 90's 0n the rotor cap ends the make it easier to install.
|
Forum: Early V8 (1932-53)
04-10-2015, 08:04 PM
|
Replies: 8
Views: 1,425
Re: early plug wire sets
Thanks for the offer but I have one, going to disassemble it and clean it up. any body have the instructions to set it up with out a distributor machine. I found the instruction to set up a two bolt,...
|
Forum: Early V8 (1932-53)
04-10-2015, 02:58 PM
|
Replies: 8
Views: 1,425
|
Forum: Early V8 (1932-53)
04-10-2015, 01:32 PM
|
Replies: 8
Views: 1,425
early plug wire sets
I have a 36 lb 221 ci. I'm changing back to an early dist. (scrapping the mallory) Any body know who sells early plug wires and dist. caps. Also what the difference between the plug wire orientation...
|
Forum: Early V8 (1932-53)
03-26-2015, 06:23 PM
|
Replies: 2
Views: 955
|
Forum: Early V8 (1932-53)
03-26-2015, 05:18 PM
|
Replies: 2
Views: 955
Installing radio
I am installing a radio in my 32, 221 flathead, converted to 12volt what is the best plug and wire combo? Is there a filter that can be installed on the 12 volt supply
|
Forum: Early V8 (1932-53)
03-10-2015, 08:49 AM
|
Replies: 33
Views: 6,067
|
Forum: Early V8 (1932-53)
03-10-2015, 07:17 AM
|
Replies: 8
Views: 1,934
Re: columbia ?
tried a echlin ( napa) VT-6184 12-6 volt reducer, 12.2 volt in 12.2 volts out. does a volt reducer actualy drop voltage or just adjust ohm's.
|
Forum: Early V8 (1932-53)
03-09-2015, 07:42 AM
|
Replies: 8
Views: 1,934
Re: columbia ?
I have a new ballast resistor part # D1110-A, for a corvette, is this compatible?
|
Forum: Early V8 (1932-53)
03-09-2015, 07:01 AM
|
Replies: 8
Views: 1,934
columbia ?
Can you run a 42-48 shift solenoid on 12 volt, being that it is a momentary connection.:confused:
|
Forum: Early V8 (1932-53)
03-04-2015, 07:29 PM
|
Replies: 42
Views: 7,305
Re: C i d #
OK all this talk about pie is making me hungry.
|
Forum: Early V8 (1932-53)
03-04-2015, 06:12 AM
|
Replies: 42
Views: 7,305
|