Forum: Model A (1928-31)
06-14-2024, 04:23 AM
|
Replies: 47
Views: 1,833
Re: Rear Diff Plug HELP
* pedant mode on *
sorry for being a bit anal and, hopefully not, confusing the original poster...
Not all pipe threads are tapered, that is plainly wrong. For instance most (1) female pipe...
|
Forum: Model A (1928-31)
06-13-2024, 08:57 AM
|
Replies: 11
Views: 511
Re: Exhaust Fumes
Really neat, i wish i could buy some on this side of the pond. Maybe next time i am in the us.
Thanks for the tip...
|
Forum: Model A (1928-31)
06-05-2024, 12:51 PM
|
Replies: 29
Views: 1,349
Re: help! clutch won‘t disengage…
yes, this failure mode has been suggested, but, as i saw something moving within the flywheel housing, i ruled it out. stupid me.
looking at the arm on the photos, it looks really fragile and it...
|
Forum: Model A (1928-31)
06-05-2024, 11:48 AM
|
Replies: 29
Views: 1,349
Re: help! clutch won‘t disengage…
i have to say thank you to all the people answering on this thread, some people were on the right track but i didn‘t believe them… see the photos attached.
Tom
|
Forum: Model A (1928-31)
06-03-2024, 05:58 AM
|
Replies: 23
Views: 2,000
|
Forum: Model A (1928-31)
05-30-2024, 03:49 AM
|
Replies: 29
Views: 1,349
Re: help! clutch won‘t disengage…
well, i made it home but the car is in a garage in Leverkusen. I cannot do that repair in my little garage so i have to find a professional to do the job.
Do any of the german members here know...
|
Forum: Model A (1928-31)
05-29-2024, 12:35 PM
|
Replies: 29
Views: 1,349
|
Forum: Model A (1928-31)
05-29-2024, 11:59 AM
|
Replies: 29
Views: 1,349
|
Forum: Model A (1928-31)
05-29-2024, 11:53 AM
|
Replies: 29
Views: 1,349
|
Forum: Model A (1928-31)
05-29-2024, 11:43 AM
|
Replies: 29
Views: 1,349
|
Forum: Model A (1928-31)
05-29-2024, 11:28 AM
|
Replies: 29
Views: 1,349
|
Forum: Model A (1928-31)
05-29-2024, 11:23 AM
|
Replies: 29
Views: 1,349
help! clutch won‘t disengage…
okay, managed about 30mls before…
the clutch pedal fell to the floor, clutch won‘t disengage but i can see the ‚clutch bearing‘ move in and out when i move the pedal…
i noticed before that the...
|
Forum: Model A (1928-31)
05-29-2024, 06:11 AM
|
Replies: 18
Views: 766
Re: Leak on top of carb...
i have not had time yet to check the carb, but a thought crossed my mind...
My mixture screw is more or less closed, maybe the vacuum pulls in the fuel into the top of the carb and after the...
|
Forum: Model A (1928-31)
05-28-2024, 08:27 AM
|
Replies: 22
Views: 1,637
|
Forum: Model A (1928-31)
05-28-2024, 08:04 AM
|
Replies: 60
Views: 3,491
Re: Idle Mixture Screw
better to put a little pressue on it and use leak detection spray (used for checking gas (natural gas, propane) pipework for leaks. Should be readily available in any diy-store for a small amount of...
|
Forum: Model A (1928-31)
05-27-2024, 12:45 AM
|
Replies: 18
Views: 766
Re: Leak on top of carb...
guys,
thank you all, i will go through and check everything. I have been out over the weekend doing about 150 miles without any problems except i have to remember to shut the fuel off when...
|
Forum: Model A (1928-31)
05-26-2024, 12:05 PM
|
Replies: 18
Views: 766
|
Forum: Model A (1928-31)
05-26-2024, 10:57 AM
|
Replies: 18
Views: 766
|
Forum: Model A (1928-31)
05-26-2024, 10:38 AM
|
Replies: 18
Views: 766
|
Forum: Model A (1928-31)
05-26-2024, 10:14 AM
|
Replies: 18
Views: 766
Leak on top of carb...
Hi guys,
this is puzzling... at least to me...
I came to the car yesterday and found a puddle of fuel under it, about 1,5l. My carb has always been leaking but it was only dripping, not a lot....
|
Forum: Model A (1928-31)
05-14-2024, 06:39 AM
|
Replies: 10
Views: 602
Re: Blown exhaust gasket and rough idle?
my method of finding leaks in the inlet or exhaust train is to duct-tape the positive-pressure side of my vacuum cleaner (Hoover?) onto the carburettor or exhaust. then i use leak-detection spray and...
|
Forum: Model A (1928-31)
04-25-2024, 02:14 PM
|
Replies: 31
Views: 3,121
Re: Recommended Turning Signal Switch
Werner,
i am sorry you have had a bad experience with Berts. my experience is mixed, they do ship, but the communication is lacking. My favourite supplier is Snyders, but they do not sell this...
|
Forum: Model A (1928-31)
04-24-2024, 04:00 PM
|
Replies: 31
Views: 3,121
Re: Recommended Turning Signal Switch
Werner,
that's also been my experience with Bert's... But the parts arrived, so i assume that they are just not good at communicating. And, being sent by USPS, it may take three weeks for the...
|
Forum: Model A (1928-31)
04-17-2024, 03:10 AM
|
Replies: 13
Views: 2,650
|
Forum: Model A (1928-31)
04-09-2024, 11:36 AM
|
Replies: 14
Views: 993
Re: Condenser Capacity
'cause 1 F(arad) = 1 C(oulomb)/1V(olt), so this is the standard version in the S.I. system.
and 1Coulomb = 1Ampere * 1 second
|