Forum: Model A (1928-31)
04-05-2024, 09:20 PM
|
Replies: 20
Views: 1,477
|
Forum: Model A (1928-31)
02-22-2024, 04:38 PM
|
Replies: 10
Views: 800
Re: Oil, pan, front seal retainer
Yes, mine does have the whole at the bottom of the trough. I tried to repair the solder because a chunk of it was missing, but ended up heating it up too much so I scraped it all out. Should I...
|
Forum: Model A (1928-31)
02-21-2024, 01:32 PM
|
Replies: 10
Views: 800
Oil, pan, front seal retainer
I’m calling it a retainer only because I do not know what it would be called but my question is why is it lined with solder?
|
Forum: Model-A
12-10-2023, 08:02 PM
|
Replies: 0
Views: 344
|
Forum: Model A (1928-31)
12-02-2023, 02:22 PM
|
Replies: 18
Views: 3,257
|
Forum: Model A (1928-31)
10-07-2023, 10:03 AM
|
Replies: 13
Views: 1,866
Re: Coil Hookup Backwards
Take a look at this from another discussion on Ford barn.
https://mgaguru.com/mgtech/ignition/ig104.htm
|
Forum: Model A (1928-31)
08-12-2023, 10:55 PM
|
Replies: 4
Views: 644
Re: Seven tooth steering box bushing removal
I have just now tried the bearing puller suggestion, and the bearing did not move at all. Then I tried a long pipe down the length of the steering column, while the bearing puller was still...
|
Forum: Model A (1928-31)
08-02-2023, 01:41 PM
|
Replies: 23
Views: 2,674
|
Forum: Model A (1928-31)
07-31-2023, 11:01 PM
|
Replies: 4
Views: 644
Re: Seven tooth steering box bushing removal
Thanks for the good information. Looks like I’m going to have to buy another tool.
For removing the upper bushing just below the steering wheel. This is a pretty good YouTube idea.
...
|
Forum: Model A (1928-31)
07-31-2023, 02:18 PM
|
Replies: 4
Views: 644
Seven tooth steering box bushing removal
How do you remove and replace the steering shaft bushing that is located above the worm gear on a seven tooth gearbox without having to remove the upper steering column bushing?
|
Forum: Model A (1928-31)
05-30-2023, 06:38 PM
|
Replies: 10
Views: 1,601
Re: Beavertail fender’s
Has anyone have information about whether or not all left hand emergency brake vehicles should or should not have Beavertail rear fenders?
|
Forum: Model A (1928-31)
05-24-2023, 08:41 PM
|
Replies: 10
Views: 1,601
Beavertail fender’s
I have a early 28 roadster that I’m not sure of its production date. It does have left hand E- break and other things that tell me it’s at least a mid production. My question is, is it supposed to...
|
Forum: Model A (1928-31)
04-20-2023, 07:50 PM
|
Replies: 7
Views: 1,349
Re: Mysterious snaps
Thanks to everyone for their input. I did check my top and I was wondering what the other snips on the back window flap was for, now I know thanks to all.
|
Forum: Model A (1928-31)
04-18-2023, 06:12 PM
|
Replies: 7
Views: 1,349
Mysterious snaps
What are these three snaps installed on the interior roof of my ragtop used for? (1928 roadster)
|
Forum: Model-A
04-10-2023, 05:26 PM
|
Replies: 0
Views: 644
1928 roadster, upper hinge
Need one upper hinge for a roadster to replace the broken one. Two vendors that I did order new were wrong and could not use them. Also, let me know if there is a reliable retailer to purchase new....
|
Forum: Model A (1928-31)
03-31-2023, 12:01 PM
|
Replies: 30
Views: 7,448
Re: "New" option for turn signals
I purchased the same ones from Amazon, but I removed them because they would not hold a charge very long and even after recharging sometimes one or two would not even work. I am now in the process of...
|
Forum: Model A (1928-31)
02-26-2023, 11:55 AM
|
Replies: 10
Views: 1,313
|
Forum: Model A (1928-31)
02-03-2023, 09:18 PM
|
Replies: 18
Views: 2,210
Re: Replacement throttle shaft
I did have the shaft down further in the voice while I was peening, but I raised it up just for the picture. And yes I do feel good that I came out not too bad. Thanks again for everyone’s input.
|
Forum: Model A (1928-31)
02-03-2023, 07:17 PM
|
Replies: 18
Views: 2,210
Re: Replacement throttle shaft
Thanks for all the suggestions I tried them, but I found that just using wood blocks in my voice and placing the butterfly into the slot so the slot wouldn’t collapse with clamping pressure.
|
Forum: Model A (1928-31)
02-02-2023, 12:01 AM
|
Replies: 18
Views: 2,210
Replacement throttle shaft
How do you attach the throttle arm to a new replacement throttle shaft? Looks like they’re peened over but how do you do it without destroying the shaft?
|
Forum: Model A (1928-31)
01-14-2023, 12:31 PM
|
Replies: 11
Views: 2,395
|
Forum: Model A (1928-31)
11-22-2022, 09:13 PM
|
Replies: 64
Views: 8,399
Re: WD40 as hand cleaner
The best home concoction hand cleaner I have ever used is an equal amount of Dawn and sugar on the palm of your hand. The sugar acts like pumice but dissolves as you wash your hand. If water is not...
|
Forum: Model A (1928-31)
09-21-2022, 09:59 AM
|
Replies: 3
Views: 825
|
Forum: Model A (1928-31)
07-20-2022, 08:56 PM
|
Replies: 25
Views: 6,509
Re: Coil replacement
Wow that’s a lot of information for a simple question that I asked but it’s all good knowledge. I hooked up my black wire to the negative side of the new coil. I then use the lead pencil test and...
|
Forum: Model A (1928-31)
07-12-2022, 05:38 PM
|
Replies: 25
Views: 6,509
Coil replacement
My old coil does not have plus or minus marked on the terminals just indicates distributor terminal. My question is this the positive or negative terminal?
|