Forum: Model A (1928-31)
12-02-2020, 08:55 PM
|
Replies: 6
Views: 1,980
|
Forum: Model A (1928-31)
11-29-2020, 10:59 PM
|
Replies: 48
Views: 7,475
|
Forum: Model A (1928-31)
11-26-2020, 04:36 PM
|
Replies: 48
Views: 7,475
|
Forum: Model A (1928-31)
11-25-2020, 09:41 PM
|
Replies: 48
Views: 7,475
|
Forum: Model A (1928-31)
10-22-2020, 10:35 PM
|
Replies: 11
Views: 2,186
Re: Car cover question
https://www.covercraft.com/us/en/product/custom-tan-flannel-car-cover.C-CCFL
COVERCRAFT
Custom Flannel Car Cover
|
Forum: Model A (1928-31)
10-20-2020, 10:33 PM
|
Replies: 12
Views: 3,024
|
Forum: Model A (1928-31)
10-15-2020, 07:35 AM
|
Replies: 20
Views: 2,564
|
Forum: Model A (1928-31)
10-15-2020, 05:10 AM
|
Replies: 20
Views: 2,564
|
Forum: Model A (1928-31)
10-10-2020, 05:48 AM
|
Replies: 21
Views: 4,052
|
Forum: Model A (1928-31)
10-10-2020, 05:42 AM
|
Replies: 18
Views: 6,040
Re: Zenith Carb Leak Puzzle
It’s safe practice to turn the gas valve off after use but the carb should not leak if you leave it on. Your float valve seams to be leaking. Use a good original steel valve. Your problem is probably...
|
Forum: Model A (1928-31)
10-04-2020, 07:07 AM
|
Replies: 9
Views: 1,489
Re: Front wheel wobble
This is how Ford specified wheel bearing adjustment in the Jan and April 1928 Service Bulletins
Adjusting Front Wheel Bearing
If there is excessive play in the bearing it can be adjusted as...
|
Forum: Early V8 (1932-53)
09-29-2020, 11:59 AM
|
Replies: 15
Views: 2,240
|
Forum: Early V8 (1932-53)
09-29-2020, 11:50 AM
|
Replies: 15
Views: 2,240
|
Forum: Early V8 (1932-53)
09-26-2020, 08:05 AM
|
Replies: 15
Views: 2,240
|
Forum: Early V8 (1932-53)
09-26-2020, 06:38 AM
|
Replies: 15
Views: 2,240
1947 Lincoln Zephyr
I have a barn find 47 H series V12 with 22,970 original miles. The vehicle was last driven in 1964. I have no keys to the car. The trunk is locked. My question is what is the truck button function?...
|
Forum: Model A (1928-31)
09-03-2020, 01:02 PM
|
Replies: 21
Views: 2,694
Re: engine / trans install question
If you’re trying to install the engine separate and after the transmission is installed you need to reach in the bell housing access cover and turn the transmission shaft while a buddy slides the...
|
Forum: Model A (1928-31)
08-12-2020, 08:37 PM
|
Replies: 14
Views: 1,833
Re: Clutch pressure plate New or Reconditioned?
www.fortwayneclutch.com reman Model A pressure plates.
Get your clutch disk from brattons they sell disks with spring guards.
Send them your brattons clutch disk and they will set the fingers to...
|
Forum: Model A (1928-31)
08-09-2020, 07:36 AM
|
Replies: 18
Views: 4,596
Re: Carb identify
I’ve been told Ford sold these too as replacements before the Tillotsons
|
Forum: Model A (1928-31)
08-05-2020, 05:14 AM
|
Replies: 15
Views: 3,321
|
Forum: Model A (1928-31)
08-02-2020, 09:18 AM
|
Replies: 11
Views: 1,392
Re: Manifold
Unless it’s show buy the new combo intake and exhaust manifolds. Use gland rings and 2 piece copper show gasket. If you can, add the aries exhaust. You will have a leakless system and a model A...
|
Forum: Model A (1928-31)
07-21-2020, 09:00 PM
|
Replies: 1
Views: 1,070
Re: Front Brake Shaft -
Bob I would buy new correct length rods and make sure you get 15 degree forward slant with the levers. If you can’t obtain the 15 degrees you could install the little brake pills or replace the brake...
|
Forum: Model A (1928-31)
07-12-2020, 02:14 PM
|
Replies: 26
Views: 5,991
Re: Rear spring spreader
It’s safer not to remove the spring attached to the rear end. Remove the rear end then remove rear spring. Wrap the spring with a chain before removing from car
|
Forum: Model A (1928-31)
07-01-2020, 10:58 PM
|
Replies: 31
Views: 6,046
Re: 600w oil
https://www.kellerheartt.com/products/shell-omala-s2-g-680-5-gallon-pail?variant=19399813070959
|
Forum: Model A (1928-31)
07-01-2020, 08:04 AM
|
Replies: 37
Views: 10,971
|
Forum: Model A (1928-31)
06-20-2020, 07:41 AM
|
Replies: 23
Views: 3,927
Re: Assistance Needed !
You should always lower the coolant level first. Seepage goes both ways I would get the coolant level down and change your oil immediately. Don’t put coolant back in until that stud is tight again
|