Forum: Early V8 (1932-53)
Today, 09:39 PM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
Maybe to use late heads on an early block...I can't remember all the details but I think that's it. If you have an early block handy see if that hole overhangs the deck.
|
Forum: Early V8 (1932-53)
06-10-2024, 09:44 PM
|
Replies: 12
Views: 405
Re: ‘53 ran hot, then missing badly. Head gasket?
Exactly. No problem there. If it's a steady miss at idle, remove one plug wire at a time from the distributor cap. If one makes no difference, that is the cylinder misfiring. From there you check the...
|
Forum: Early V8 (1932-53)
06-10-2024, 09:33 PM
|
Replies: 511
Views: 36,899
|
Forum: Early V8 (1932-53)
06-10-2024, 11:33 AM
|
Replies: 511
Views: 36,899
|
Forum: Early V8 (1932-53)
06-09-2024, 10:21 AM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
Quote:
"It don't take but country smarts to build a driveshaft"
Ol' Smokey knew his stuff! :D;) And so do you. Love the home built shaft plan. :cool: That lathe sure has been a handy...
|
Forum: Early V8 (1932-53)
06-08-2024, 09:59 PM
|
Replies: 2
Views: 143
|
Forum: Early V8 (1932-53)
06-07-2024, 12:47 PM
|
Replies: 511
Views: 36,899
|
Forum: Early V8 (1932-53)
06-07-2024, 07:10 AM
|
Replies: 6
Views: 465
|
Forum: Early V8 (1932-53)
06-06-2024, 09:39 PM
|
Replies: 20
Views: 811
Re: New versus old valve springs
It does sound as if you have the late "rotator" type springs but the early retainers. The early springs are longer and will fix your mismatch. That's the way I'd go.
|
Forum: Early V8 (1932-53)
06-06-2024, 06:12 PM
|
Replies: 511
Views: 36,899
|
Forum: Early V8 (1932-53)
06-06-2024, 06:02 PM
|
Replies: 23
Views: 781
Re: 80 years ago today
We owe those allies a lot. Everything, in fact. We should all do our best to make sure our young people don't forget-starting with our own families.
|
Forum: Early V8 (1932-53)
06-05-2024, 05:37 PM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
Nice pics. Standing on the front is classic! One thing different when I put the later engine in the '41...the carb mount pad on the manifold is at a different angle than the early engine's and the...
|
Forum: Early V8 (1932-53)
06-04-2024, 10:00 PM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
Well, you got me. The belt is routed down around that idler (cut down from an idler on a John Deere 4 cyl) which mounts to a threaded hole in the slingshot bracket. The alternator is cheated forward...
|
Forum: Early V8 (1932-53)
06-04-2024, 09:52 PM
|
Replies: 8
Views: 394
Re: 1940 master cylinder repair kit
As Kurt said above, the washer goes in the cylinder first, and sits at the very bottom of the bore...clear at the end. Then the check valve and spring, cup and piston. The washer's job is sealing the...
|
Forum: Early V8 (1932-53)
06-04-2024, 06:01 PM
|
Replies: 10
Views: 443
|
Forum: Early V8 (1932-53)
06-03-2024, 06:51 PM
|
Replies: 511
Views: 36,899
|
Forum: Late V8 (1954+)
06-03-2024, 12:34 PM
|
Replies: 12
Views: 486
Re: Rear end squealing/whining
If it never makes the noise unless the truck is moving it's not the clutch throwout bearing.
If you can't run the truck on stands with wheels spinning I don't know how you'll isolate the noise...
|
Forum: Early V8 (1932-53)
06-03-2024, 12:27 PM
|
Replies: 511
Views: 36,899
|
Forum: Late V8 (1954+)
06-02-2024, 08:01 AM
|
Replies: 12
Views: 486
|
Forum: Early V8 (1932-53)
06-02-2024, 07:57 AM
|
Replies: 11
Views: 416
Re: 1940 V8 Cam / valve timing
You actually did a very good job. The lash mistake is an honest one, and is not uncommon especially if someone doesn't do this for a living. Making your own timing tape and using a damper you have on...
|
Forum: Early V8 (1932-53)
06-01-2024, 10:27 PM
|
Replies: 38
Views: 6,597
Re: chevy dizzy for flatheads
If you use a carburetor other than the stock unit, the vacuum source for the Ford distributor will not be correct and the timing curve will be wrong. Also, the Ford distributor used ONLY vacuum to...
|
Forum: Early V8 (1932-53)
06-01-2024, 03:42 PM
|
Replies: 511
Views: 36,899
|
Forum: Early V8 (1932-53)
06-01-2024, 11:50 AM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
A post above referenced the larger engine pulling more vacuum, causing the power valve to open earlier.
This is backward. The power valve is held closed by vacuum and when vac drops the...
|
Forum: Early V8 (1932-53)
05-31-2024, 01:38 PM
|
Replies: 511
Views: 36,899
Re: 276 stroker from 35 years of parts
What Denny says...vaseline is great for the pump priming.
One of my old instructors called vaseline "bedroom salve". You put it on the door knob to keep the kids out.
|
Forum: Early V8 (1932-53)
05-31-2024, 01:35 PM
|
Replies: 6
Views: 407
Re: Tolerance-Ford aluminum heads
At first it would seem that way. However, any excess out-of-flat in either direction will require some extra amount of bolt torque to overcome the warp and bring the head back to flat. From that...
|