Forum: Early V8 (1932-53)
Today, 01:51 PM
|
Replies: 11
Views: 428
Re: Voltage regulator, generator wiring (12 volt)
The early voltage regulators were mounted on rubber bushings so that the buzz of the VR pole wouldn't be detectable. This required a ground of the VR case to the system so they took it directly to...
|
Forum: Early V8 (1932-53)
Today, 01:34 PM
|
Replies: 8
Views: 261
Re: three brush regulator
The 2-stage unit was a cut out with an extra control relay. The control relay would allow the generator to charge until the battery was fully charged. With the battery charged, the system voltage...
|
Forum: Model A (1928-31)
Today, 11:29 AM
|
Replies: 18
Views: 566
Re: knowing when my car was made
Engines were stamped after they passed the operational test with the big electric motors that turned them. If they passed the amp load check of the big electric motor and there were no leaks then the...
|
Forum: Model A (1928-31)
Today, 10:50 AM
|
Replies: 16
Views: 573
Re: model a engine
Pull the head and see if it has original type valves and standard size pistons. Pull the valve chamber cover and see if it still has solid tappets and two piece guides. Pull the pan and look at a...
|
Forum: Model T (1909-1927)
Today, 10:24 AM
|
Replies: 5
Views: 249
Re: Aluminum alloy model T wheels
One way that they could be aluminum would be if the individual spokes were cast from aluminum then assembled like OEM wood spokers would be. The spokes appear to be individual. I also wonder how wood...
|
Forum: Model A (1928-31)
05-24-2024, 10:46 AM
|
Replies: 18
Views: 566
Re: knowing when my car was made
With so much water under the bridge, it is near impossible to get an exact day no matter what branch assembly plant may have been involved. Most major assemblies were sent in batches from the Rouge...
|
Forum: Model A (1928-31)
05-19-2024, 11:01 AM
|
Replies: 10
Views: 558
Re: Aaaa
The Soviets loved the Studebaker trucks we supplied them during WWII but they were still manufacturing the GAZ model AA pattern trucks as fast as they could. Ford Dearborn manufactured big twin V8...
|
Forum: Early V8 (1932-53)
05-18-2024, 11:04 AM
|
Replies: 14
Views: 617
|
Forum: Early V8 (1932-53)
05-18-2024, 10:52 AM
|
Replies: 19
Views: 781
Re: '46 Coupe 59AB Starter
The green bible indicates that the 18-11005 armature was used in starters for the early 8BA (7RA). The number was likely changed later in the 8BA era but they are likely interchangeable. The ones for...
|
Forum: Model A (1928-31)
05-18-2024, 10:16 AM
|
Replies: 35
Views: 4,984
Re: Phaeton top rest question
In aviation we always referred to the metal ones as Willkie button plugs. They have a multitude of sizes. They are used to plug holes in instrument panels and sheet metal access holes. There are also...
|
Forum: Model A (1928-31)
05-16-2024, 10:10 AM
|
Replies: 17
Views: 736
Re: Fuse size
Henry had intelligent people designing his systems but the era that the model Ts and As were manufactured in left a lot to be desired on a safety standpoint. Fuses were not common until the early 30s...
|
Forum: Early V8 (1932-53)
05-15-2024, 01:21 PM
|
Replies: 10
Views: 549
Re: What color are these cars?
Early in the 30s Ford had light maroon and medium maroon. By 1939, they had 3 or 4 different maroons and some darker reds as well. This is from the Auto Color Library....
|
Forum: Model A (1928-31)
05-15-2024, 12:08 PM
|
Replies: 17
Views: 736
Re: Fuse size
Rob Doe has it. The fuse is to protect the wire. Each different American wire gauge (stranded AWG) size has a corresponding fuse size to protect it. This link has a chart on page 505 of the PDF...
|
Forum: Early V8 (1932-53)
05-14-2024, 06:56 PM
|
Replies: 14
Views: 617
Re: 1940 Ford Zenith Radio
I'd keep the vibrator if it's still functional. The old sets are a good learning tool about radio sets. They were actually pretty simple but as was mentioned, the caps or capacitors like to pop like...
|
Forum: Early V8 (1932-53)
05-14-2024, 06:06 PM
|
Replies: 16
Views: 754
Re: Nice forty Ford
After the dust storms back in the early 30s, some folks started getting serious about protecting their vehicles from such situations. A lot of roads in rural farming communities were pretty dusty...
|
Forum: Model A (1928-31)
05-14-2024, 05:37 PM
|
Replies: 12
Views: 716
Re: my project and my thanks...
There is a lot to be said about running these old flivers whether they are restored or just good drivers. They are a lot of fun either way.
|
Forum: Model A (1928-31)
05-14-2024, 10:40 AM
|
Replies: 7
Views: 415
Re: charging
I have digital and analog meters and use both. My Fluke digital was purchased to adjust voltage output on aircraft 24-volt systems so they would charge at 28-volts. The fluke was the most accurate...
|
Forum: Early V8 (1932-53)
05-13-2024, 03:43 PM
|
Replies: 9
Views: 360
Re: What water pumps do I need?
FWI, the 37 through 48 pumps will bolt up to the engine but they only work well when the whole front of the motor is converted to early style. This also requires the early style cam and gearing to...
|
Forum: Early V8 (1932-53)
05-13-2024, 03:35 PM
|
Replies: 11
Views: 698
Re: Looking for a quality 6 Volt Starter
1 gauge or larger cable is what 6-volt systems like for starter motors. Heat related problems can sometimes be an open in an armature winding. They will pass current until it expands from engine heat...
|
Forum: Model A (1928-31)
05-13-2024, 11:44 AM
|
Replies: 3
Views: 374
Re: Henry and Edsel again
That delivery certainly had all the bells and whistles. Dual chrome plated horns and dual windshield wipers plus chrome hub covers. That was quite a delivery van.
Henry and Edsel wer always around...
|
Forum: Model A (1928-31)
05-13-2024, 11:22 AM
|
Replies: 37
Views: 1,482
Re: How many miles should spark plugs last?
How long the electrodes last depends on what they are made from. The resistors are another fail point in plugs so equipped. If you purchase iridium electrode plugs then the resistor will likely be...
|
Forum: Model A (1928-31)
05-13-2024, 10:14 AM
|
Replies: 15
Views: 721
Re: Grease in 2-tooth
Some folks use John Deere corn header gearbox grease for it's thixotropic nature. It is fluidic when parts move in it but more of a jell state when parts are at rest. It is a brownish color so that...
|
Forum: Model A (1928-31)
05-12-2024, 08:35 AM
|
Replies: 11
Views: 429
Re: How do I test field coils in a starter?
Starter motors are shunt wound with heavier guage wire in order to get a really good torque output. By changing to series wound fields, it just reduces the torque capability. The original fields on...
|
Forum: Early V8 (1932-53)
05-11-2024, 08:18 AM
|
Replies: 14
Views: 677
Re: Ballast resistor for 12V coil
Most 12-volt systems are regulated to 13.5 to 14-volts when the alternator or generator is in function. A 6-volt system should run at around 7.1 to 7.2-Volts.
|
Forum: Early V8 (1932-53)
05-10-2024, 10:59 AM
|
Replies: 14
Views: 677
Re: Ballast resistor for 12V coil
The built in resistor is a misnomer that I see a lot. It just has more resistance in the primary coil. The higher resistance primary makes more heat but modern internal insulation is a specific epoxy...
|