Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.08 seconds. Search: Posts Made By: Gary WA
Forum: Model A (1928-31) Today, 01:26 PM
Replies: 7
Views: 224
Posted By Gary WA
Re: Do the Motor Mounts get wired around the bolts

Les Andrews Mechanic book.
Forum: Model A (1928-31) Today, 12:08 PM
Replies: 7
Views: 224
Posted By Gary WA
Re: Do the Motor Mounts get wired around the bolts

Yes
Forum: Model A (1928-31) Yesterday, 08:44 PM
Replies: 21
Views: 632
Posted By Gary WA
Re: I give up

Just for idea? Gas cap properly vented!
Forum: Model A (1928-31) Yesterday, 06:46 PM
Replies: 21
Views: 632
Posted By Gary WA
Re: I give up

Just saw another carb installed doing the same thing.! Cast iron fuel filter or glass bowl? Also installing fuel line into carb too far will restrict fuel flow!
Forum: Model A (1928-31) Yesterday, 06:33 PM
Replies: 21
Views: 632
Posted By Gary WA
Re: I give up

Have you checked Idle Air adjustment screw(mis-adjusted or too short) or dirt/rust. Next time it dies stop and remove gas line to ensure it is getting fuel and not plugged with rust??
Forum: Model A (1928-31) 06-02-2024, 02:56 PM
Replies: 8
Views: 427
Posted By Gary WA
Re: Gear Grind After Clutch Adjustment

Or put the arm back to where it was!
Forum: Model A (1928-31) 05-30-2024, 12:31 PM
Replies: 4
Views: 380
Posted By Gary WA
Re: ‘29 Briggs 60B Fordor Pinstripe

will this help French Grey is correct
Forum: Model A (1928-31) 05-29-2024, 01:40 PM
Replies: 21
Views: 796
Posted By Gary WA
Re: help! clutch won‘t disengage…

As per post #4 Broken pin or worn threads! you stated the pedal went to the floor? A pin or something has broken loose.
Forum: Model A (1928-31) 05-29-2024, 12:22 PM
Replies: 21
Views: 796
Posted By Gary WA
Re: help! clutch won‘t disengage…

any of these parts missing or broken
Forum: Model A (1928-31) 05-29-2024, 11:56 AM
Replies: 21
Views: 796
Posted By Gary WA
Re: help! clutch won‘t disengage…

Is your shaft collar and pin still intact?
Forum: Model A (1928-31) 05-28-2024, 11:43 AM
Replies: 12
Views: 1,112
Posted By Gary WA
Re: Stupid question of the day. (maybe the year)

like this? There are no stupid questions in the Model A Community!!
Forum: Model A (1928-31) 05-27-2024, 07:05 PM
Replies: 18
Views: 709
Posted By Gary WA
Re: Power Loss After Carb Rebuild

jet sizes with ONE Gasket!! tight! NO gasket on idle jet.
Forum: Model A (1928-31) 05-27-2024, 04:42 PM
Replies: 18
Views: 709
Posted By Gary WA
Re: Power Loss After Carb Rebuild

Is your throttle assembly arm bent? that bolts to rear of motor!
Forum: Model A (1928-31) 05-26-2024, 01:51 PM
Replies: 18
Views: 697
Posted By Gary WA
Re: Leak on top of carb...

also that gasket looks like the water outlet gasket not carb gasket
Forum: Model A (1928-31) 05-26-2024, 01:49 PM
Replies: 18
Views: 697
Posted By Gary WA
Re: Leak on top of carb...

Make sure all the jets are tight with one gasket, no gasket on idle jet.
Forum: Model A (1928-31) 05-25-2024, 08:42 PM
Replies: 12
Views: 647
Posted By Gary WA
Re: Another carb needs repair

Article i found in my Library!
Forum: Model A (1928-31) 05-25-2024, 08:18 PM
Replies: 10
Views: 488
Posted By Gary WA
Re: electrical charging problem

Have a load test done on battery! and check your cut out may be stuck! There will be many more suggestions!!
Forum: Model A (1928-31) 05-24-2024, 09:50 PM
Replies: 12
Views: 647
Posted By Gary WA
Re: Another carb needs repair

No, but what type zenith?
Forum: Model A (1928-31) 05-24-2024, 03:46 PM
Replies: 6
Views: 485
Posted By Gary WA
Re: Ford Tool Identification

Another excellent tool book charts and info. And Judging Standards MAFCA has info
Forum: Model A (1928-31) 05-23-2024, 09:21 PM
Replies: 2
Views: 303
Posted By Gary WA
Re: Radiator Bracket Repair

Take it to a radiator shop and have it soldered back on!
Forum: Model A (1928-31) 05-23-2024, 04:19 PM
Replies: 18
Views: 640
Posted By Gary WA
Re: knowing when my car was made

do you have the frame number and does it match the motor number?
Forum: Model A (1928-31) 05-22-2024, 06:21 PM
Replies: 17
Views: 771
Posted By Gary WA
Re: how to repair top casting on sidebowl carburetor???

Yes find a good welder and he will be able to properly weld it for you! Been there done that! Or try and find a new top!put word out at local club or maybe contact Berts model a parts he might have...
Forum: Model A (1928-31) 05-22-2024, 03:32 PM
Replies: 6
Views: 709
Posted By Gary WA
Re: Model A Ford tools

www.fordtoolcollector.org in Missouri.
Forum: Model A (1928-31) 05-22-2024, 03:13 PM
Replies: 6
Views: 399
Posted By Gary WA
Re: Looking for production numbers on a Panel Truck

Ill take a look! What i find is 245 in Canada plus many more produced thru out the world. Germany Belgium Denmark Italy France etc.
Forum: Model A (1928-31) 05-22-2024, 09:14 AM
Replies: 6
Views: 399
Posted By Gary WA
Re: Looking for production numbers on a Panel Truck

sent email
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:59 PM.