Forum: Model A (1928-31)
06-22-2024, 09:08 PM
|
|
Replies: 10
Views: 479
Re: I need help installing a horn rod
I just ran into the same problem and what I call a dirt dobber had filled the tube, find a steel rod long enough to reach and try to clean it out ,also people beat on end of shaft and brad where it...
|
|
Forum: Early V8 (1932-53)
06-16-2024, 11:56 AM
|
|
Replies: 7
Views: 276
|
|
Forum: Model A (1928-31)
06-14-2024, 06:27 AM
|
|
Replies: 5
Views: 298
Re: Valve lapping procedure
If you have a machine shop close or know someone that has a vacuum checker this will let you know for sure if they are sealing or not, lot of work to put together and do over...
|
|
Forum: Model A (1928-31)
06-11-2024, 06:14 PM
|
|
Replies: 11
Views: 542
Re: Carb leak
If you take the gas line loose at carb and the gas valve is off there should be no gas coming out of gas line, if there is gas valve is bad
|
|
Forum: Model A (1928-31)
06-07-2024, 08:41 PM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
06-07-2024, 12:10 PM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
06-07-2024, 12:07 PM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
06-07-2024, 12:03 PM
|
|
Replies: 7
Views: 535
|
|
Forum: Model A (1928-31)
06-07-2024, 11:46 AM
|
|
Replies: 47
Views: 2,029
Re: Rear Diff Plug HELP
If it was mine I would weld a large nut to it , should come out easy, sometimes easy outs makes a easy job hard
|
|
Forum: Model A (1928-31)
06-07-2024, 05:51 AM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
06-07-2024, 05:47 AM
|
|
Replies: 7
Views: 535
Re: Wobbly dist—hard to disgnose/fix?
this might give you an idea of what it's doing if it's the shaft, if the whole dist. is moving need to check dist. lockdown
https://youtu.be/sAImvK8dnl4?si=ff9fiWIBL1FXnnKT
|
|
Forum: Model A (1928-31)
05-25-2024, 06:07 AM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
05-24-2024, 08:12 PM
|
|
Replies: 23
Views: 1,528
|
|
Forum: Model A (1928-31)
05-24-2024, 07:15 AM
|
|
Replies: 26
Views: 1,540
Re: Dropping the oil pan
Here's a video I did a while back, hope it will give you some idea's
https://youtu.be/8MH3HtTnshQ?si=sJpUHdzJUb3x0ew0
|
|
Forum: Early V8 (1932-53)
05-14-2024, 12:28 PM
|
|
Replies: 16
Views: 914
Nice forty Ford
Wondering if this is an original air cleaner?https://youtu.be/XTODrDPUAKI?si=HZPSjS_eFZ8VDQQ0
|
|
Forum: Model A (1928-31)
05-12-2024, 08:39 AM
|
|
Replies: 10
Views: 711
Re: Water Neck Modification
If you tap it on the rear, you only tap deep enough to have a couple threads and thats ok, or maybe I should say only enough that fitting will only thread in a couple threads, if you go deeper the...
|
|
Forum: Model A (1928-31)
05-11-2024, 08:34 PM
|
|
Replies: 12
Views: 686
Re: Tight crank gear
Here"s how I install the crank gear
https://youtu.be/s2vTWWAYo1I?si=p7n_T-AyVSOxqtXb
|
|
Forum: Model A (1928-31)
05-11-2024, 05:13 PM
|
|
Replies: 29
Views: 2,192
Re: Sticking valves?
This will give you an ides of how it's done
https://youtu.be/07v6AERzVQQ?si=oWJ0UQLKyuGojWjE
|
|
Forum: Model A (1928-31)
05-07-2024, 08:54 AM
|
|
Replies: 29
Views: 2,192
|
|
Forum: Model A (1928-31)
05-04-2024, 08:06 PM
|
|
Replies: 29
Views: 2,192
Re: Sticking valves?
I have a 66 ford f 100 and use to if I let it sit for anytime the valves would stick and bend push rods when I tried to start , I poured a couple bottles of Stihl two cycle chainsaw oil in gas tank...
|
|
Forum: Model A (1928-31)
04-17-2024, 07:08 AM
|
|
Replies: 7
Views: 1,217
|
|
Forum: Model A (1928-31)
03-29-2024, 07:46 PM
|
|
Replies: 30
Views: 2,313
|
|
Forum: Early V8 (1932-53)
03-21-2024, 12:02 PM
|
|
Replies: 96
Views: 7,095
Re: Break-in gone wrong!
I threaded the holes and used pipe plugs on the one I just did. don't like those original style oil plugs
|
|
Forum: Model A (1928-31)
03-20-2024, 09:14 PM
|
|
Replies: 29
Views: 2,281
Re: Deep knocking sound
This might help and give you a little insight to what to do
https://youtu.be/8MH3HtTnshQ?si=RGbjJ5dRa5xOqvOw
|
|
Forum: Early V8 (1932-53)
03-20-2024, 09:06 PM
|
|
Replies: 21
Views: 1,398
|
