Forum: Model A (1928-31)
06-08-2024, 05:02 PM
|
Replies: 5
Views: 276
|
Forum: Model A (1928-31)
06-08-2024, 01:48 PM
|
Replies: 5
Views: 161
Re: Gear Drive Starter Question
This is from Terry Burtz new engine guide.
"The new flywheel does not come with a ring gear installed because the beveled teeth on the ring gear need to be at the rear if using a Model A starter,...
|
Forum: Model A (1928-31)
06-07-2024, 01:42 PM
|
Replies: 28
Views: 2,895
Re: Distributor won't drop in fully...
The short answer is probably not as it's hard to get to the lower shaft because of the spring that hold the oil pump drive gear in place. I had one that was really stuck and I had to make a collet...
|
Forum: Model A (1928-31)
06-06-2024, 08:10 PM
|
Replies: 5
Views: 276
|
Forum: Early V8 (1932-53)
06-06-2024, 05:25 PM
|
Replies: 41
Views: 1,570
Re: Front Axle 1939 Ford pickup
The lock pin for the king pin is the same 1928-48 and I have the blue prints for the Model A axle and the hole is reamed .561-.563,
it's not tapered.
|
Forum: Early V8 (1932-53)
06-06-2024, 11:16 AM
|
Replies: 41
Views: 1,570
|
Forum: Early V8 (1932-53)
06-05-2024, 10:03 AM
|
Replies: 14
Views: 368
|
Forum: Early V8 (1932-53)
06-04-2024, 03:31 PM
|
Replies: 8
Views: 379
|
Forum: Model A (1928-31)
06-04-2024, 12:41 PM
|
Replies: 1
Views: 139
Re: Connecting the light switch
The notch in the contact plate and the lower part of the switch
go in a tab in the upper part of the switch. You can see the tab in the picture right above the bolt.
|
Forum: Model A (1928-31)
06-04-2024, 12:11 PM
|
Replies: 9
Views: 494
|
Forum: Model A (1928-31)
06-01-2024, 09:04 PM
|
Replies: 3
Views: 383
|
Forum: Model A (1928-31)
06-01-2024, 02:16 PM
|
Replies: 24
Views: 1,069
|
Forum: Model A (1928-31)
05-31-2024, 09:38 PM
|
Replies: 24
Views: 1,069
|
Forum: Model A (1928-31)
05-29-2024, 10:06 AM
|
Replies: 27
Views: 1,665
Re: Move A By Yourself
Here you go, ain't cheap. https://duckduckgo.com/?t=h_&q=light+airplane+tug&iax=shopping&ia=shopping
|
Forum: Early V8 (1932-53)
05-27-2024, 02:42 PM
|
Replies: 41
Views: 1,570
|
Forum: Model A (1928-31)
05-25-2024, 02:29 PM
|
Replies: 6
Views: 412
|
Forum: Early V8 (1932-53)
05-25-2024, 10:09 AM
|
Replies: 8
Views: 564
Re: Brake stud repair tool
Here is a link to Vince's site showing how to swage the stud.
https://www.fordgarage.com/pages/swaging.htm
|
Forum: Model A (1928-31)
05-24-2024, 09:04 PM
|
Replies: 14
Views: 472
|
Forum: Model A (1928-31)
05-24-2024, 11:00 AM
|
Replies: 6
Views: 508
|
Forum: Early V8 (1932-53)
05-23-2024, 08:15 PM
|
Replies: 12
Views: 370
Re: Stake bed gate hinges
Could you modify these to make what you need?
https://www.buyersproducts.com/product/straight-stake-rack-connector-set-753
|
Forum: Model A (1928-31)
05-23-2024, 06:41 PM
|
Replies: 11
Views: 767
Re: Nothing Seems to Fit!
Do you have another sector shaft that you can try the pitman arm
on to see which part is the problem?
|
Forum: Early V8 (1932-53)
05-23-2024, 04:44 PM
|
Replies: 12
Views: 370
|
Forum: Model A (1928-31)
05-23-2024, 10:28 AM
|
Replies: 14
Views: 472
|
Forum: Model A (1928-31)
05-22-2024, 07:41 PM
|
Replies: 16
Views: 1,084
Re: 1931 model a engine
Another way to check the flatness of the block and head is like
Terry Burtz show in the builders guide.
"Place short pieces of oiled Plastigage around various locations on the cylinder block,...
|
Forum: Model A (1928-31)
05-22-2024, 01:42 PM
|
Replies: 18
Views: 813
|