|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-22-2014, 01:49 PM | #1 |
Member
Join Date: Mar 2013
Location: Fishers, IN
Posts: 53
|
Motometer reading
How do you read/interpret a Motometer? I see the "mercury" move up and down based upon temperature:, but there is no calibration to relate it to. Thanks!
|
08-22-2014, 02:10 PM | #2 |
Senior Member
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,559
|
Re: Motometer reading
There is a simple way to guesstimate the temperature by looking at the mercury rising in the car. Get a near thermometer, or some other cheap thermometer with the range of 0-4-- degrees and pull over while driving normally and measure the temperature of the radiator water. Note where the mercury is. Then do it when it is a hot day and the mercury is quite a bit higher. You will have some base points. Use caution and a rag, don't get scalded. If the car is steaming, wait a spell. Most motometers have some type of scale on one face, turn that one to be visible from the drivers seat.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-22-2014, 02:24 PM | #3 |
Senior Member
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,116
|
Re: Motometer reading
When my As are in motion and air is being drawn through by the fan and the motion of the car, I rarely ever see any mercury on the motometer- maybe 1/8 inch on really hot days. When idling, it might go up 1/2" or so.
|
08-22-2014, 02:35 PM | #4 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Motometer reading
If I remember correctly, I thought the motometer, at least mine does, noted what was going on as far as the temp of the car. The mercury would go up and as it goes up I thought you could read what was happening with the motor-like run temp, boil temp, etc..
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
08-22-2014, 03:09 PM | #5 |
Senior Member
Join Date: Jun 2010
Location: Danvers, Ma.
Posts: 715
|
Re: Motometer reading
You're right Fred, Also in the little circle hole near the top, it would read "summer average".
Ten1is; do you have the inner plate that's supposed to face the driver in behind the thermometer glass? This is where your info is printed in the Motometer. |
08-22-2014, 05:22 PM | #6 |
Senior Member
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
|
Re: Motometer reading
Sponsored Links (Register now to hide all advertisements)
When new, they hardly ever read, except when near boiling . After a few months, you will get the inevitable gaps of air in the red fluid. This has worked great for me. Both of my motometers now work in a visible area of sight. The air seems to have settled down the bottom out of sight and just pushes the red up higher . No, I am not going to freeze them or swing them around my head to get the red back down . |
08-22-2014, 07:02 PM | #7 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,911
|
Re: Motometer reading
Mine is the same. I look at a motometer as more of a indication when the water is boiling because it can't possibly read an accurate temperature since the bulb doesn't even reach the water level (until the water is boiling out the top of the radiator... ).
|
08-22-2014, 07:47 PM | #8 |
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,181
|
Re: Motometer reading
I have both old original, 60s repro and old "aftermarket'---i think messco or something like that ---they all read accuratly, and only will get the "air bubbles" if laid on the side with the top lower than the bottom, i have compared top tank temps to the reading and they are close even with the coolant level at the bottom of the baffle, there is a line just below the opening --cold motor, use radiator cover ---this is 140-150,just above the top of the open circle is boiling---that is when I get steam out the overflow
years ago my father bought and sold many motormeters, unless the glass tube was broken they worked, and were accurate |
08-22-2014, 09:08 PM | #9 |
Senior Member
Join Date: Jun 2010
Location: Danvers, Ma.
Posts: 715
|
Re: Motometer reading
What exactly is the red fluid? I can't see it being Mercury since that is silver metal and I don't think one can dye it red. I've had old Motometers that seem pretty accurate but I got a new one for the A, and doesn't work very well. I went back to just the plain cap. Maybe the old type fluid had something to do with the accuracy back in the day.
|
08-24-2014, 12:16 AM | #10 |
Senior Member
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
|
Re: Motometer reading
|
08-24-2014, 01:21 AM | #11 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Motometer reading
If you have gaps in the RED CRAP, let it idle, with the radiator mostly covered with cardboard, until the lower red goes up & touches the "other" reds & remove said cardboard, & all the red will come down together! COMPRENDE' ?
And DON'T swing thet thing around on a rope, might break yo' head ur yo' windshield!! ur hit yo' po' Dog ur yo' Mother-in-Law ---Your wife is smart enuff to stay in the HOUSE, while she calls the "FUNNY-FARM" Bill W. (OH! and while cruising along with a Moto-Meter, if the temp goes UP & Down in regular 2 to 3 minute intervals, YOU ARE LOW ON WATER!! And don't forget the roofing nail trick, like, jist drop it in the top of the overflow tube & give sum nails to your friends!)
__________________
"THE ASSISTANT GURU OF STUFF" |
08-24-2014, 01:40 AM | #12 |
Senior Member
Join Date: Jun 2014
Location: Oregon
Posts: 132
|
Re: Motometer reading
With a good balanced cooling system the motometer is great.
__________________
Simplicity is the ultimate sophistication. L.D. I have 40 horses in the garage. Only feed them when I want to take them out. 31 Model A Tudor 55B Nick |
08-24-2014, 07:18 AM | #13 |
Senior Member
Join Date: Oct 2012
Location: beautiful down town Passaic NJ
Posts: 293
|
Re: Motometer reading
you can also tap the air pockets out of the motometer by firmly banging the lower end on a tire or a soft piece of wood, kind of the way you shake down a thermometer .
|
08-24-2014, 08:38 AM | #14 |
Senior Member
Join Date: Feb 2014
Location: Warrnambool, Victoria, Australia
Posts: 800
|
Re: Motometer reading
My motometer seems to have TWO different liquids. A clear/silver liquid column is visible most times (which I thought might have been mercury?). When the car reaches operating temperature, a red column just starts to poke up into the visible zone. I'm confused because the clear/silver liquid appears to have breaks in the column. You can see this in the photo, taken after a 20 min run in the car. The red is just visible at the bottom, but there is a definite second column with what appears to be two air bubbles in it, one large and one small.
What's going on here? I confess to laying the motometer sideways while topping up the radiator before I knew better. |
08-24-2014, 08:59 AM | #15 |
Senior Member
Join Date: Oct 2013
Location: Duluth, MN
Posts: 196
|
Re: Motometer reading
I open the cap and heat the brass bulb on the bottom with a heat gun till the red reaches the top when it comes back down it is connected.
|
08-24-2014, 11:28 AM | #16 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Motometer reading
I had a small antique thermometer laying on the dash of my car. The interior of the car got so hot that the bulb was broken and the red alcohol spilled out.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|