Forum: Late V8 (1954+)
05-13-2024, 08:12 PM
|
Replies: 8
Views: 307
Re: Timken a150 pinion seal
Your 1954 Ford F250 is fitted with a Rockwell differential , metal cased spring loaded: dimensions: ID 1.875 (1.7/8) X 3.252 (3.1/4) OD X .500 (1/2) W.
|
Forum: Model A (1928-31)
05-09-2024, 09:30 PM
|
Replies: 4
Views: 381
Re: Wheel bearin question
1931 Ford Model A rear wheel bearing, FORD part number: B1225A, HYATT 00536,
1948 V8 model Ford rear wheel bearing, FORD part number: 68-1225A, HYATT A1444,
00536 Dimensions: ID 2.062 (2.1/16) X...
|
Forum: Early V8 (1932-53)
04-04-2024, 09:02 PM
|
Replies: 11
Views: 813
Re: 48 Ford car rear hub bearing dimensions
19Fordy,
Yes the same FORD bearing part numbers: 68-1225&68-1236 were used in 1939&1940 model FORDS except for trucks Mercury also used the same Bearing part numbers,
HYATT A1444, sleeve : HYATT...
|
Forum: Model A (1928-31)
04-04-2024, 08:41 PM
|
Replies: 30
Views: 8,400
Re: Bearing on King Pins question
Most of the T83 Timken type : TTSP are only available in ACE chinese brand, sometimes wer'e lucky &we can source TIMKEN T83, I'd try United Bearing Company in Texas they'll have them in Timken.
|
Forum: Early V8 (1932-53)
03-26-2024, 07:02 PM
|
Replies: 11
Views: 813
|
Forum: Early V8 (1932-53)
03-26-2024, 06:52 PM
|
Replies: 11
Views: 813
Re: 48 Ford car rear hub bearing dimensions
There should be a inner race/split sleeve that fits over the bearing, so as the bearing doesn't wear the shaft, WHY FORD DIDN'T use Timken tapered roller bearings begs disbelief SMH....., defies...
|
Forum: Early V8 (1932-53)
03-20-2024, 06:22 PM
|
Replies: 9
Views: 761
Re: Front seals
The seal's the problem being far &way too big it has to&must be 1.312 (1.5/16),
Also the redi sleeve ID is also far&way too big it too has to&must be 1.312 (1.5/16),
1.500 is i.5-2 MM bigger than...
|
Forum: Early V8 (1932-53)
03-03-2024, 06:40 PM
|
Replies: 38
Views: 2,080
|
Forum: Early V8 (1932-53)
03-03-2024, 06:37 PM
|
Replies: 38
Views: 2,080
|
Forum: Early V8 (1932-53)
03-01-2024, 09:10 PM
|
Replies: 38
Views: 2,080
|
Forum: Early V8 (1932-53)
03-01-2024, 09:08 PM
|
Replies: 38
Views: 2,080
|
Forum: Late V8 (1954+)
02-18-2024, 08:15 PM
|
Replies: 8
Views: 602
Re: seal
Kultulz,
Are you referring to me as being a " so -called specialty vendor"?......,
We've been in business for 54 years......
|
Forum: Late V8 (1954+)
02-16-2024, 06:41 PM
|
Replies: 8
Views: 602
Re: seal
National 6371, 410539, 450539,480539,411978N,410467, 450467.
|
Forum: Early V8 (1932-53)
01-15-2024, 07:54 PM
|
Replies: 15
Views: 970
Re: Rear axle leaking
Tim,
ALL felt washers&leather oil seals require soaking overnight(24hrs),
To soften up the leather, NEVER EVER install them dry because they'll wear the shaft,
&Sometimes cause a groove where the...
|
Forum: Early V8 (1932-53)
01-14-2024, 05:44 PM
|
Replies: 15
Views: 970
Re: Rear axle leaking
I'd strongly advise&suggest as far as oil seals are concerned see if you can find,locate, search&seek the O.E.M/ORIGINAL FORD oil seals, as these are metal cased leather lip&are better suited to...
|
Forum: Model T (1909-1927)
01-11-2024, 06:42 PM
|
Replies: 10
Views: 1,122
Re: Fan Belt Slips Off
Try a slightly smaller ID belt ,
That way it's sits tightly in the groove,
Also use CRC belt grip to help lubricate the belt.
|
Forum: Early V8 (1932-53)
01-02-2024, 10:32 PM
|
Replies: 14
Views: 1,008
|
Forum: Early V8 (1932-53)
01-02-2024, 10:11 PM
|
Replies: 14
Views: 1,008
Re: dana 41 outer axle bearing upgrade?
Do you have the Ford part numbers for the bearings?,
My Timken catalog 1945-1961 lists these Timken part numbers: 1948-F1-8HC, 8RC,
Rear wheel inner: cone 3984, inner cup,3920,
,Rear wheel outer:...
|
Forum: Model A (1928-31)
12-28-2023, 07:22 PM
|
Replies: 12
Views: 914
Re: Transmission bearings .. sealed or unsealed?
The open side is always fitted/installed so as that's lubricated by the transmission/engine oil,
The sealed/sheilded side is to prevent foreign matter/objects entering through the bearing into the...
|
Forum: Model A (1928-31)
12-28-2023, 07:20 PM
|
Replies: 12
Views: 914
|
Forum: Model A (1928-31)
12-11-2023, 06:33 PM
|
Replies: 57
Views: 11,122
Re: Cluster bearing solution?
The problem is NO ONE is getting them made in the O.E.M./ORIGINAL HYATT style, i.e. with the spiral grooves not even BOWER or RBC were making them with these spiral grooves even the new copies...
|
Forum: Early V8 (1932-53)
11-14-2023, 06:07 PM
|
Replies: 7
Views: 881
Re: Wheel bearings?
Wheel bearing part number is: 88128R ( complete with locking collar/retainer),
Try& get either: FAFNIR/FEDERAL/L&S/NDH USA made brands or BCA/FAG GERMAN ONLY! NOT INDIAN/KOREAN/SKF european made ,...
|
Forum: Early V8 (1932-53)
10-12-2023, 06:58 PM
|
Replies: 7
Views: 538
Re: 48 grease seal
Was the bearing oil seal neoprene rubber lip or O.E.M./ORIGINAL A1 (leather lipped)?,
If it's the former there known to cause leaking ,
As the rubber material gets hot it gets hard &sometimes wears...
|
Forum: Early V8 (1932-53)
09-19-2023, 07:35 PM
|
Replies: 5
Views: 551
Re: 39 transmission bearing cross reference
According to my Australian BSC (Bearing Service Company) automotive application catalogs,
The driveshaft rear is a : 6208 (FORD 51A7025),
Mainshaft rear : 6306 (FORD 51A7065),
Both bearings are...
|
Forum: Model A (1928-31)
09-11-2023, 07:09 PM
|
Replies: 21
Views: 3,609
Re: Remember 9/11/01
I wonder if the REAL truth will ever come out/be revealed?.......,
I was on my way to work when i heard it on the wireless news station i was listening to,
Disbelief,horror,shock&stunned, years...
|