Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-11-2020, 11:47 PM   #1
Otterby
Junior Member
 
Otterby's Avatar
 
Join Date: Oct 2017
Location: Casper, WY
Posts: 27
Default Drag Link Question

I’m installing a NOS drag link in my ‘48 Super Deluxe. The fixed ball joint end included a flat washer and a rubber washer. How do these set on the ball joint stud. Does the flat washer sit against the ball joint or against the spindle arm? I believe that it’s supposed to sit against the ball joint but being flat it’s going to let the grease escape easily. Or will it conform to the ball joint as the nut is tightened?
Otterby is offline   Reply With Quote
Old 08-11-2020, 11:49 PM   #2
mobileparts
Senior Member
 
Join Date: Feb 2014
Location: West Hempstead, New York
Posts: 167
Default Re: Drag Link Question

Unless you have a very changed front end,
Ford didn't have Ball Joints until 1954.....
mobileparts is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-12-2020, 03:04 AM   #3
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,100
Default Re: Drag Link Question

Quote:
Originally Posted by mobileparts View Post
Unless you have a very changed front end,
Ford didn't have Ball Joints until 1954.....

Look toward the left side of the drawing and you will see the "ball" joint he's referring to on his drag link......perfectly-stock front end! DD


__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 08-12-2020, 05:36 AM   #4
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,730
Default Re: Drag Link Question

^^ It's interesting that that drag link, while adjustable, is not infinitely adjustable. It can only be adjusted to the nearest thread pitch, which is, admittedly, perfectly adequate in that situation.

It is also interesting (to me at least) that the ball joints have a full ball. the ones I have cut apart have a big hemisphere on the taper stud side and a smaller hemisphere on the closed side.

Yes I'm an engineering nerd.

Sorry I can't answer about the washers without seeing the parts. The aim is to seal the joint so it should be obvious if the parts are correct.

Mart.
Mart is offline   Reply With Quote
Old 08-12-2020, 07:34 AM   #5
Kube
Senior Member
 
Kube's Avatar
 
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,893
Default Re: Drag Link Question

Quote:
Originally Posted by Otterby View Post
I’m installing a NOS drag link in my ‘48 Super Deluxe. The fixed ball joint end included a flat washer and a rubber washer. How do these set on the ball joint stud. Does the flat washer sit against the ball joint or against the spindle arm? I believe that it’s supposed to sit against the ball joint but being flat it’s going to let the grease escape easily. Or will it conform to the ball joint as the nut is tightened?
Here's a photo that should help.
Attached Images
File Type: jpg drag link ends 2MK.jpg (29.0 KB, 52 views)
__________________
"I can explain it for you. However, I can't understand it for you".
Kube is offline   Reply With Quote
Old 08-12-2020, 08:04 AM   #6
Otterby
Junior Member
 
Otterby's Avatar
 
Join Date: Oct 2017
Location: Casper, WY
Posts: 27
Default Re: Drag Link Question

Sponsored Links (Register now to hide all advertisements)
Thanks for the help. I guess I shouldn't be calling the ends ball joints. They're the same as tie rod ends, just on a drag link and not a tie rod. It looks like my flat washer should be cupped to match the contour of the ball. I think I'll just use the washer off of my old end.
Otterby is offline   Reply With Quote
Old 08-12-2020, 08:11 AM   #7
Don Rogers
Senior Member
 
Don Rogers's Avatar
 
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
Default Re: Drag Link Question

Otterby, I think part of the problem is that your flat washer should be a cupped washer as Mr. Kube has shown. It serves as a seal
Don Rogers is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:07 AM.