01-29-2020, 10:13 PM | #1 |
Senior Member
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
|
8cm cam grind
I have an 8cm camshaft that does not look too bad but when I chucked it in the lathe and measured the lift I found values between 0.330 and 0.320. One was at 0.335. These numbers were repeatable. My question is can this cam be the ground to something acceptable close to stock? I know the base circle changes but I think this will not be much of an issue.
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound |
01-29-2020, 10:17 PM | #2 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,179
|
Re: 8cm cam grind
Frank:
I believe Tilden Technologies does have a "hot" stock grind. It may be the EAB cam profile or something like that. Check out their webpage or give them a call. https://www.tildentechnologies.com/ Good luck. |
Sponsored Links (Register now to hide all advertisements) |
|
01-29-2020, 10:29 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,067
|
Re: 8cm cam grind
Also, 'Pete' Samuelson (here is on here as 'Pete') can grind all sorts of great profiles - I imagine he has something that would work for you. I'd drop him a PM or eMail and see what he says . . .
|
01-30-2020, 08:40 PM | #4 |
Senior Member
Join Date: Oct 2019
Location: Carthage , Tennessee
Posts: 199
|
Re: 8cm cam grind
Pete has my cam right now,,,,,he has a good reputation.
Tommy |
01-30-2020, 09:28 PM | #5 |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,960
|
Re: 8cm cam grind
I can put a stock Mercury grind on you cam core. I am in New Zealand for a few weeks so would have to be when I return.
Cheers Tony |
01-31-2020, 05:44 AM | #6 |
Senior Member
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
|
Re: 8cm cam grind
Sponsored Links (Register now to hide all advertisements)
__________________
“The technique of infamy is to start two lies at once and get people arguing heatedly over which is true.” ~ Ezra Pound |
01-31-2020, 06:04 AM | #7 | |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: 8cm cam grind
Quote:
Also suspect that grinding it in an attempt to make it perfect will not produce any noticeable difference in performance.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES |
|
01-31-2020, 07:16 AM | #8 |
Senior Member
Join Date: May 2010
Location: albany
Posts: 466
|
Re: 8cm cam grind
I agree with this
|
01-31-2020, 08:56 AM | #9 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,179
|
Re: 8cm cam grind
|
01-31-2020, 09:30 AM | #10 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: 8cm cam grind
I'm using a stock EAB cam in the 280, and am real pleased with it;s performance. Torque is amazing
|
01-31-2020, 09:42 AM | #11 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,179
|
Re: 8cm cam grind
Pete or Tony:
I have an EAB cam that has a damaged lobe. I'll try to get pict, but it has a chip in one of the lobes. Can something like this be successfully repair? |
01-31-2020, 10:06 AM | #12 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 8cm cam grind
I have a Mercury engine in my '51 Ford. I had an Isky MAX-1 to install in it, but after checking the specs on the "Tilden" page and some discussion here, I left the stock cam and saved the Isky for a later build. In retrospect, I think I did the right thing.
|
01-31-2020, 11:01 AM | #13 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,431
|
Re: 8cm cam grind
The EAB cam was the last one FoMoCo made for the flathead V8 engines. It was designed to replace the 8BA cam to give the cars more torque for those that still had 239 CID. The 8CM cam was desiged for the Mercury 255 to give it a bit more torque. The Mercury cars were heavier than Ford beginning in 1949 but by 1952, the cars were a lot more similar in weight so the 239 needed a boost. The EAB cam was the replacement cam for all of them and Ford had them available for a long time after flathead production stopped. I still find NOS ones now and then.
|
01-31-2020, 11:12 AM | #14 |
Senior Member
Join Date: May 2013
Location: Harrisonburg, VA
Posts: 842
|
Re: 8cm cam grind
I wonder what the specs. are on an EAB cam?
|
01-31-2020, 01:47 PM | #15 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: 8cm cam grind
They are very similar to the 8CM specs. .330 lift. 205 deg. duration at .050 lift.
|
01-31-2020, 03:25 PM | #16 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 8cm cam grind
Just out of curiosity, does anyone know if there are "1CM" ('51 Mercury) or "EAC" ('52-'53 Mercury) separate grinds?
|
01-31-2020, 04:07 PM | #17 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,526
|
Re: 8cm cam grind
I do have a 1CM cam. Haven't plotted it though.
|
01-31-2020, 04:12 PM | #18 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,316
|
Re: 8cm cam grind
|
01-31-2020, 04:16 PM | #19 |
Senior Member
Join Date: May 2010
Location: Wa.
Posts: 5,408
|
Re: 8cm cam grind
It can be fixed,BUT, at $80 bucks a pound for the welding rod it is not practical any more. When the core bank runs dry we will go back to fixing them.
|
01-31-2020, 04:23 PM | #20 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,179
|
Re: 8cm cam grind
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|