|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-03-2013, 04:40 PM | #1 |
Senior Member
Join Date: May 2012
Location: Corbett OR
Posts: 233
|
I need a set of .020 32-38 rod bearings
Need a set of .020 (68-6211) rod bearings. The rod size is standard, and the crank side is .020 over. I have been all over the web and have not been able to find .020 size. Seems as there are alot of odd sizes for sale. Most people are using 59ab engines and not rebuilding the stock ones, I had no idea how hard they would be to find. The machine work is done on my 37 engine. Any help would be Greatly appreciated. Thanks Ron
Last edited by rottenron36; 04-03-2013 at 04:44 PM. Reason: needed to add a line |
04-03-2013, 05:53 PM | #2 |
Senior Member
Join Date: May 2010
Location: new zealand
Posts: 1,054
|
Re: I need a set of .020 32-38 rod bearings
these are flanged right? try patricks
|
Sponsored Links (Register now to hide all advertisements) |
|
04-03-2013, 06:08 PM | #3 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: I need a set of .020 32-38 rod bearings
Try Fred Wilner, Southside Obsolete, Faribualt MN. He has a web site with his phone number.
|
04-03-2013, 06:18 PM | #4 |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,960
|
Re: I need a set of .020 32-38 rod bearings
remind me this weekend & I will look in my stash .
I got a big stash |
04-04-2013, 01:18 AM | #5 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: I need a set of .020 32-38 rod bearings
Try Stacy Brown in Arlington, TX
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
04-04-2013, 10:06 AM | #6 |
Senior Member
Join Date: May 2012
Location: Corbett OR
Posts: 233
|
Re: I need a set of .020 32-38 rod bearings
Sponsored Links (Register now to hide all advertisements)
|
04-04-2013, 03:56 PM | #7 |
Member
Join Date: May 2010
Location: Wichita, KS
Posts: 88
|
Re: I need a set of .020 32-38 rod bearings
Good luck with your search. Your best bet will be contacting the folks that frequent this site or HAMB. I ran into the exact same trouble 4 years ago with my '36 motor. None of the parts vendors had them, even though most of them listed them in their online catalog (at least they used to). I ended up spending about a day on the phone looking for them 'old school' (no internet). The ones I was looking for were also 0.020/STD, and I got all but one pair from EGGE. I may have exhausted their supply of them but you might try them anyway. I don't remember now where the 4th pair came from but it seems to me it was from a guy in St. Cloud, MN. I will see if I have anything on it in my files later and let you know.
|
04-04-2013, 04:05 PM | #8 |
BANNED
Join Date: May 2010
Location: Gothenburg Nebraska Just off I-80
Posts: 4,893
|
Re: I need a set of .020 32-38 rod bearings
If you have the old Federal Mogul numbers I may have some. Several boxes of old bearings and unable to find the part numbers in the only FM book I have. Seems like all the parts in the book are 1946 and newer. Rod
|
04-05-2013, 09:56 AM | #9 |
Senior Member
Join Date: May 2012
Location: Corbett OR
Posts: 233
|
Re: I need a set of .020 32-38 rod bearings
Thanks again for all your help. I found a set of federal mogul standard bearings on ebay. The # they used is 9020 ca. Also if KiWinUS could look in his stash I would appreciate it. Thanks Ron
|
04-05-2013, 10:48 AM | #10 |
BANNED
Join Date: May 2010
Location: Gothenburg Nebraska Just off I-80
Posts: 4,893
|
Re: I need a set of .020 32-38 rod bearings
I will do some digging. For some reason I had set back a set of 9805's thinking that was the correct FM part number. Will see what I have in 9020's as that number rings a bell. Thanks Rod
|
04-05-2013, 11:03 AM | #11 |
Senior Member
Join Date: Nov 2010
Location: Lancaster PA
Posts: 535
|
Re: I need a set of .020 32-38 rod bearings
You might try Mac at vanpeltsales.com if you haven't already.
|
04-05-2013, 02:18 PM | #12 |
BANNED
Join Date: May 2010
Location: Gothenburg Nebraska Just off I-80
Posts: 4,893
|
Re: I need a set of .020 32-38 rod bearings
Looks like the 9805's are for the later flatheads. Still have not gotten to dig for the ones you are looking for. Rod
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|