Peter Tommasini 2015 US/Canada Metalshaping Classe

[fordcragar]

This year Peter will be visiting the United States in September/November. He will be attending Metalmeet in Oblong Il and Santa Cruz, plus conducting some 4 day classes in the following areas before and/or after Metalmeet.

The following is a list of the class hosts and their email addresses. If you would like to attend one of the following classes, send an email, with your information (phone number and email address) to the host of the class that you are thinking about attending.

Nashville area, Tennessee ……………..September 17-20………Jim Hery….....…[email protected]
Rock Hill, South Carolina………………...September 24-27………Will Cronkite……[email protected]
Leonardtown, Maryland…………………..October 1-4………………Robert McCartney …[email protected]
Dennison Minnesota.……………………....October 8-11……………Dan Pate…….………[email protected]
Fort Collins/Denver, Colorado ……….October 20-23……………Bob Adame…………[email protected]
Vancouver BC, Canada ......……..……October 26-29……………Rick Bartok…..……[email protected]
Portland, Oregon ..............………..…..November 5-8……………Carl Morton………[email protected]
Everett (Seattle/Tacoma) Washington .…November 12-15…Rick Young…………[email protected]

If you are interested in attending one of the events in the cities listed above or have questions, get on the list, even if the event is filled or sold out, this list will be used as a standby list as well, just in case someone has to drop out before the class starts. So put your name on the list and pay when asked, the first people that paid will be placed in the class. The attendance with each class will be between 5 and 10 depending on venue size and interest. In talking to some of the hosts, it appears that a lot of these classes will fill up fast as they seem to have a list of people already that will attend.

Class cost:
The cost for the four day (hands on) class will be $650; which could include lunches (check with the host). The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.

[Mike V. Florida]

https://www.fordbarn.com/forum/showthread.php?t=175388

[fordcragar]

Thanks Mike for pointing that out, but if you look through Will's thread, you won't see the Seattle/Everett class mentioned. Will did a nice job advertising his and some of the other classes. The Seattle class was going to be the first class this year (in September), but some medical problems came up with the host so it was postponed and rescheduled in November.

Just like last year, I'll post again class participation updates.

[fordcragar]

Whether you are a beginner or an experienced metalshaper, anyone that takes one of these classes will learn. We had quite a range of experience level at the Seattle class a couple of years ago and everyone benefited.


Nashville area, Tennessee ………….............5
Rock Hill, South Carolina………………......….Full -- waiting list 1
Leonardtown, Maryland………………….....….Full -- waiting list 2
Dennison Minnesota.…………………….......…6
Fort Collins/Denver, Colorado ………....…..3
Vancouver BC, Canada ......……..………....Full -- waiting list 0
Portland, Oregon ..............………..….......6
Seattle/Everett Washington..................3

If you would like to attend one of the classes or to put your name on a waiting list, contact a host in the city you would like to attend:

Class cost:
The cost for the four day (hands on) class will be $650; which could include lunches (check with the host). The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.[/B]

[Mike V. Florida]

Originally Posted by fordcragar

Just like last year, I'll post again class participation updates.

Just trying to put the two threads together, sometimes it's hard to follow changing information in two different threads.

[RockHillWill]

Sponsored Links (Register now to hide all advertisements)

Sorry about that Larry. When you mentioned about the Seattle class not being held, I assumed that it was cancelled, not rescheduled, and edited my first post. Thanks for the update.

[boomerusmc]

Yes...I think I got in for the Leonardtown class! Fingers crossed...

[fordcragar]

Tomorrow, the class in the Nashville area starts, so if you didn't get around to signing up for one of the other classes, it might not be too late, check with the hosts.

Whether you are a beginner or an experienced metalshaper, anyone that takes one of these classes will learn. We had quite a range of experience level at the Seattle class and everyone benefited.


Nashville area, Tennessee …………............
Rock Hill, South Carolina………………......….Full -- waiting list 1
Leonardtown, Maryland………………….....….Full -- waiting list 2
Dennison Minnesota.…………………….......…8
Fort Collins/Denver, Colorado ………....…..3
Vancouver BC, Canada ......……..………....Full -- waiting list 0
Portland, Oregon ..............………..….......7
Seattle/Everett Washington..................4

If you would like to attend one of the classes or to put your name on a waiting list, contact a host in the city you would like to attend:

Class cost:
The cost for the four day (hands on) class will be $650; which could include lunches (check with the host). The event host should be able to advise you on what tools and safety equipment to bring. All shop materials will be supplied. Any other questions, please contact the event host.