|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-03-2020, 12:10 PM | #1 |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Electronic ignition advise
Anyone running an electronic ignition on their car? I’m tired of messing with the points and sitting in the garage wanting to drive my car the same day and not being able to.
I do not see myself switching over to complete auto advanced ignition anytime soon or ever. Would just like to have a little more reliability. And someone mentioned to me already that a voltage spike kills the electronic ignition module pretty quickly. Has anyone ever had that happen?
__________________
Isaiah B. 1928 all metal Tudor |
08-03-2020, 12:17 PM | #2 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Electronic ignition advise
Wire it in correctly with good connections and it should be trouble free.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-03-2020, 12:23 PM | #3 |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Re: Electronic ignition advise
Sounds like a good idea. And I’ll keep a spare module with me at all times.
__________________
Isaiah B. 1928 all metal Tudor |
08-03-2020, 12:38 PM | #4 |
Senior Member
Join Date: May 2010
Location: Concord CA
Posts: 637
|
Re: Electronic ignition advise
The way I connected mine was direct from battery post to fuse to ignition switch. The wire on the plate is a ground wire and connected to a good chassis ground.
|
08-03-2020, 02:12 PM | #5 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: Electronic ignition advise
Before I spent that much money I'd fix what I had.
What problem(s) are you having with the original style. It's a fairly simple straight forward mechanism. JMO Paul in CT |
08-03-2020, 02:16 PM | #6 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,513
|
Re: Electronic ignition advise
Sponsored Links (Register now to hide all advertisements)
Quote:
To the original poster, I have warrantied about as many of these as I have installed. Not all were the fault of the electronics however they still failed and rendered the vehicle inoperable. If you find yourself messing with a Kettering points system, you likely have an issue elsewhere (bad distributor cam, loose base plate, excessive humidity, weak/faulty points, etc.). These cars went many, many miles with a points ignition system without trouble. When trouble did arise, a quick wipe of the contacts, and a check of the gap was all that was needed. I can tell you first-hand, that if the module fails (-and they do) then you either need to have a spare module to get you home, or someone else to bring you home. One other thing to realize, the electronic ignition does NOT give a hotter spark. That is related to your coil. Today, the quality of replacement parts for the original style ignition systems are of such that there is not any performance advantage with the electronic ignition these days. |
|
08-03-2020, 02:20 PM | #7 | |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Re: Electronic ignition advise
Quote:
__________________
Isaiah B. 1928 all metal Tudor |
|
08-03-2020, 03:32 PM | #8 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Electronic ignition advise
The problem with these units is when they go bad you are screwed if you don't have a spare. And there is no telling when that might happen. Your distributor is at fault here: a proper rebuild will give years of low maintenance service. I rebuild distributors and advertise on here if you are ever interested.
__________________
"The more things change, the more they stay the same." |
08-03-2020, 03:40 PM | #9 |
Senior Member
Join Date: Dec 2014
Location: Germantown,TN
Posts: 516
|
Re: Electronic ignition advise
On a recent tour one the cars with an electronic ignition broke down. It went home on a roll-back because no knew how to fix it.my truck quit on earlier tour. I had hardly gotten out of the truck before several had hood open and we’re changing the Chinese capacitor. I might have been down 10 minutes. This is the only problem I’ve had with Henry’s stock ignition in 5000 miles of touring. It has never failed to start immediately.
I like to keep things simple. Kettering ignitions are simple. If it were my car I would be finding out why I had continuing problems. Modifying to get around a problem without really know what the problem is, is not a good idea in my opinion. |
08-03-2020, 03:52 PM | #10 |
Senior Member
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,354
|
Re: Electronic ignition advise
The key to the electronic ignition is good clean connections. I have 40,000 trouble free miles on mine. Yes I clean connections periodically. My friend had an erratic module out of the box that gave him fits until he replaced it this weekend.
One downside to consider, is you need 4.5-5 volts to fire. That means it won’t start on a low battery. |
08-03-2020, 04:27 PM | #11 |
Senior Member
Join Date: May 2010
Location: Lock Haven Pa.
Posts: 252
|
Re: Electronic ignition advise
Funny thing is almost everyone here runs modern cars with electronic ignition and depend on it every time to start there vehicle.
I've had electronic ignition for 15yrs with no problems.Wire then correctly and they are trouble free. No muss no fuss just start and go. |
08-03-2020, 04:41 PM | #12 |
Senior Member
Join Date: May 2010
Location: Austin, Texas
Posts: 925
|
Re: Electronic ignition advise
Had one installed for years. Worked perfectly. Doing Great Race Rally in Nebraska off in the boonies at a rural intersection, i.e. a mail box, a small Post Oak tree and a lane that looked like it went nowhere, the electronic ignition decided it did not want to rally any more.
Having one of those is like having a pet rattle snake.....one day...
__________________
I noticed the harder I work the luckier I get! |
08-03-2020, 04:50 PM | #13 |
Senior Member
Join Date: May 2010
Location: Durango CO
Posts: 1,309
|
Re: Electronic ignition advise
I was the ad agency for Per-Lux that acquired the Ignitor electronic ignition system at least forty years ago. This unit was originally designed for stationary engines running 24/7, refrigeration units and fork lifts. I've used them in sail boat engines, classic Chris-Crafts, hot rods and collector cars, including five Model A's. The only failure I've experienced was 23 years ago when I did not properly ground a unit on an A speedster. If you use the proper coil, you will experience a hotter spark. Mickey Remund (Mickey Thompson's engine builder) perfected the Petronix for Model A's and early Ford V-8's before retiring and selling the program to F&S. Two things cause these units to fail; 1: improper grounding and 2: leaving the ignition on. The point (pun intended) of this post is to assure owners that electronic ignitions aren't all bad.
__________________
No restorable Model A's were harmed in the building of this truck! |
08-03-2020, 06:07 PM | #14 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: Electronic ignition advise
A friend of mine just took his Model A 4 door from NY to Florida. After the first couple of days of traveling, he was ready to replace the points with electronic ignition. After a couple more days he realized that after 5 or 6 hundred miles, he didn't have to adjust the points any more. It seems like the rubbing block wears to a certain point and then doesn't wear much after that. The last 600 miles he didn't have to adjust the point at all.
__________________
AL in NY |
08-03-2020, 07:50 PM | #15 |
Senior Member
Join Date: May 2010
Location: Englewood, Colorado
Posts: 1,372
|
Re: Electronic ignition advise
Wired right with good grounds they last almost forever. Most Model A’s have bad grounds.
|
08-04-2020, 07:56 AM | #16 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,513
|
Re: Electronic ignition advise
Quote:
Not to belabor the point, but so often we find these things failing at the most inopportune time. I think most of us here who have been around Model-As know of someone who has experienced a failure with a retrofitted electronic ignition on a Model-A. Sure, it is easy to put blame on that car owner suggesting they "should" have done this or that to prevent that failure, but none the less, it still failed. With the great quality of the Stipe cam, the modern lower plate, A&L points & condensers, ...in my view there is no real advantage of retrofitting an electronic triggering device over the Kettering system. . |
|
08-04-2020, 08:33 AM | #17 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Electronic ignition advise
The same caveats apply to the kettering system,proper connections are critical to both,so is turning the key off.The problem with points is they degrade slowly,often unnoticed loss of power as dwell increases.Rubbing block failure and misalignment doesn't occur with the electronic system either. I prefer points as they require routine maintenance, something i enjoy as much as driving the car.
|
08-04-2020, 09:22 AM | #18 |
Senior Member
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,056
|
Re: Electronic ignition advise
Some years ago when aftermarket electronic ignitions were the hot ticket, I tried a couple.
I was doing a lot of off road driving, chasing Baja races etc. I always carried a stock point plate and cap in the tool box just in case. Well, it was used more than once. To my way of thinking, the point system is the basic system, if it doesn't work there is something else wrong (mechanical wear). At the age of these cars, it is not unreasonable. But, in todays world, there are enough parts and people who can correct these worn out issues. J
__________________
As Carroll Smith wrote; All Failures are Human in Origin. |
08-04-2020, 11:12 AM | #19 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Electronic ignition advise
After a simple twelve volt conversion , using the Pertronix flame thrower coil , I can see no need to convert to electronic ignition . . As said, electronic ignition doesn't necessarily give hotter spark . The spark comes from the coil . I use the Pertronix forty thousand volt Flame thrower coil for hotter spark .
Last edited by Purdy Swoft; 08-04-2020 at 11:23 AM. |
08-04-2020, 11:33 AM | #20 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,849
|
Re: Electronic ignition advise
Do Pertronix Ignitor still have the issue of burning out if the key is left on? I remember that was the main issue with them.
I have a Pertronix Ignitor III in my '55 Ford that is awesome and have had no problems with. But it is an entirely different animal altogether; protection against leaving ignition on, adaptive dwell, multi-spark and an adjustable rev limiter. |
08-04-2020, 01:49 PM | #21 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Electronic ignition advise
Adaptive dwell is one of the advantages of electronic ignition consistent coil soak yields consistent voltage regardless of gap.With manual timing its moot ,doesnt matter how hot or cold the spark is when the timing doesn't match rpm..
|
08-04-2020, 02:26 PM | #22 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Electronic ignition advise
I would think that leaving the ignition on could ruin any coil .
|
Sponsored Links (Register now to hide all advertisements) |
|
08-04-2020, 02:31 PM | #23 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Electronic ignition advise
Some have been known to use Mallory distributors with the Pertronix coil .
|
08-04-2020, 03:19 PM | #24 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,849
|
Re: Electronic ignition advise
|
08-05-2020, 04:27 PM | #25 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Electronic ignition advise
Sorry, I know nothing about electronic ignition , that is the main reason that I don't use it . I just figure that leaving the ignition switch on isn't a good idea if the engine isn't running whether it be electronic or points ignition . .
|
08-06-2020, 09:37 AM | #26 |
Senior Member
Join Date: May 2010
Posts: 2,597
|
Re: Electronic ignition advise
Sponsored Links (Register now to hide all advertisements)
FSI uses Pertronix Ignitor II modules. Instruction sheet For Zipper says module will be damaged if key is left on with engine not running. |
08-06-2020, 04:59 PM | #27 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,184
|
Re: Electronic ignition advise
It is funny that I have been told several times “it is very reliable, mine only quit once and now I carry a spare”.
I have driven 27k miles and never had an ignition failure with my 1930 Tudor with points. John
__________________
Welcome each day |
08-06-2020, 08:00 PM | #28 |
Senior Member
Join Date: Jul 2010
Location: Aiken, South Carolina
Posts: 695
|
Re: Electronic ignition advise
Purdy did the use of the Flamethrower coil require 12 volt conversion?
|
08-06-2020, 09:02 PM | #29 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Electronic ignition advise
I was told that the twelve volt version gave best results . This is mentioned on another thread here yesterday I think .
|
08-07-2020, 12:45 AM | #30 |
Senior Member
Join Date: Jul 2013
Location: La Porte, IN
Posts: 143
|
Re: Electronic ignition advise
I have FSI ignition on mine, love it! Yes I carry an extra module, just like you carry spare points.
|
08-07-2020, 02:36 PM | #31 | |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Electronic ignition advise
Quote:
98,000 miles on my NU-Rex. 1st module. 32,000 miles on my '31 S/W FSI 1st module. I've worked on a couple cars with electronic ignition and the problem has always been an intermittent ground to the module. But I also have 2 Model A's with the standard system and don't have trouble with those either. I have replaced the points, condensers and distributor bushings a couple times. I don't have a strong preference. |
|
08-07-2020, 03:32 PM | #32 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,513
|
Re: Electronic ignition advise
Quote:
I get totally what you all are saying. I guess the thing is most of us claim to be Model-A 'restorers', ...and Yes, most of us like to upgrade things to better our vehicles. I guess if someone wants to install an electronic system just because it makes them feel better or happier, -then I say go for it. I guess I just struggle with the justification some hobbyists use when they claim they need the electronic ignition for more reliability and to be able to tour with their Model-A. A lot of misinformation out there on stuff like this. Now this is just me personally, but having to invest $50.00 +/- for a spare module as a "just in case", and then going thru the hassle to exchange an electronic module on the side of the road seems pointless when about $20.00 gives you a set of points and condenser to carry if the need ever arose which can be exchanged and set in just a few moments. I suppose this discussion is just like choosing a suitable oil for a Model-A. No right or wrong answer. |
|
08-14-2020, 12:35 PM | #33 |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Re: Electronic ignition advise
Thanks for the TONS of info guys! I read every one and great arguments from both sides.
__________________
Isaiah B. 1928 all metal Tudor |
08-14-2020, 01:59 PM | #34 |
Senior Member
Join Date: Jul 2011
Location: Southwestern Connecticut
Posts: 931
|
Re: Electronic ignition advise
Here are a few thoughts of electronic ignition systems. Yes, they are great in modern cars that were designed for it from the ground up. If they do fail, you will find five parts stores in a 20 mile range that will have the parts on the shelf. No so much with any conversion kit.
I have two 1978 motorcycles. On one I did an "upgrade" to electronic ignition about ten years ago. It was trouble-free and maintenance free for about eight years. It ran beautifully...until it didn't. When it failed I barely limped home the 45 miles on two cylinders on a major highway. It was terrifying. My testing with a multi-meter was inconclusive. It took two weeks of back and forth mail to get the module tested, confirmed bad, and replaced. The replacement module was nearly $200.00 and the module failure damaged the coil...another $100.00. My second bike I left with points. I took the time to really teach myself to maintain, adjust, and understand them (the Model A was a huge help in this regard). I keep a spare distributor plate in my storage compartment. It has new points and condensers, has been run-in tested, and I marked it so I know exactly where to set it so the timing is right. This spare set-up takes up about as much space as ham sandwich and cost less than $50.00. When I did have a breakdown, I had it swapped out and was back on the road in 15 minutes. The Model A's original system is so easy and inexpensive to maintain, I would never consider changing it. Also, I prefer the original set up to the so-called 'modern points." The original points are easier to adjust, and I can do it without feeler gauges by simply counting the turns. Whatever you decide, I wish you all the best. Ken
__________________
Style beats speed any day, and with a lot fewer tickets. |
08-17-2020, 06:57 AM | #35 | |
Senior Member
Join Date: Apr 2016
Location: St Clair, Michigan
Posts: 395
|
Re: Electronic ignition advise
Quote:
__________________
Isaiah B. 1928 all metal Tudor |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|