Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-10-2017, 08:42 PM   #1
Ziffer
Senior Member
 
Join Date: May 2010
Location: Michigan
Posts: 171
Default 8BA or 59AB to power belly tank at Bonneville

I am starting a tank project for Bonneville. Not looking to set a record but would like to have a 1950 period correct tank. Pros/Cons between the two engines. I have one of each so looking for a reason to pick one over the other.

Thanks
Z
Ziffer is offline   Reply With Quote
Old 01-10-2017, 10:43 PM   #2
RalphM
Senior Member
 
RalphM's Avatar
 
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,646
Default Re: 8BA or 59AB to power belly tank at Bonneville

Belly tanks are definitely short on space, so the Earlier motor would be the better choice. IMHO
RalphM is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-10-2017, 11:12 PM   #3
Ol' Ron
Senior Member
 
Ol' Ron's Avatar
 
Join Date: May 2010
Location: Chester Vt
Posts: 8,842
Default Re: 8BA or 59AB to power belly tank at Bonneville

As the blocks are the same length, when you put a bell housing on the 8BA. I think it depends on the transmission. You have a better selection with the 8BA and cheaper in most cases. However if money is no object, I don't think it makes much difference.
Ol' Ron is offline   Reply With Quote
Old 01-11-2017, 07:14 AM   #4
saltracer
Senior Member
 
Join Date: May 2014
Location: Lafayette, La.
Posts: 100
Default Re: 8BA or 59AB to power belly tank at Bonneville

We run a 8BA in our Bonneville cars mostly because that's what I had to start, but adapting to later transmissions is easier (in my opinion). In one car with have a blow proof bell housing with a T-5 using a SFI rated 302sbf flywheel and the other a C-4 both based on the Speedway kit.
saltracer is offline   Reply With Quote
Old 01-11-2017, 01:59 PM   #5
awelker
Member
 
awelker's Avatar
 
Join Date: May 2010
Location: Berrysburg, PA
Posts: 49
Default Re: 8BA or 59AB to power belly tank at Bonneville

"Period correct" and legal for Bonneville are two ends of the spectrum. You can be true to the 1950 time period for engine technology but to be legal for Bonneville today there will be no doubt your tank is modern. I tried to keep my bellytank as true to the period as possible, but their is no doubts once you peek at the cage under the skin.

As far as the engines, the 8ba is easier to adapt transmissions and buy an off the shelf blow proof bell housing. But the 59A is slightly more compact around the flywheel on the bottom side, but you will need to build your own flywheel shield. In the end it may come down to what you have. I use the 59A series in my bellytank.

In any case first thing is to get a rulebook and study if you haven't already. Also, check out landracing.com forums for a lot of good info.

If you would like to discuss bellytanks and Bonneville send me a pm. Also, below is a link to my Flikr page with some build and finished pics of my bellytank for reference.

https://www.flickr.com/photos/vonwelker/albums

Andy
__________________

www.vonwelker.com

https://www.flickr.com/photos/vonwelker/albums
Home of the Blonde Bitch Bellytank
awelker is offline   Reply With Quote
Old 01-11-2017, 02:07 PM   #6
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: 8BA or 59AB to power belly tank at Bonneville

Sponsored Links (Register now to hide all advertisements)
Have you torn the engines down and crack-tested them? You may answer your own question.
tubman is offline   Reply With Quote
Old 01-11-2017, 02:39 PM   #7
Ziffer
Senior Member
 
Join Date: May 2010
Location: Michigan
Posts: 171
Default Re: 8BA or 59AB to power belly tank at Bonneville

Both checked out and are good (have several others that are not good)
Ziffer is offline   Reply With Quote
Old 01-11-2017, 03:42 PM   #8
barnfind
Senior Member
 
Join Date: Jan 2011
Posts: 426
Default Re: 8BA or 59AB to power belly tank at Bonneville

awelker - I checked out your Build page. You have some serious design and execution talent!
barnfind is offline   Reply With Quote
Old 01-12-2017, 12:08 PM   #9
awelker
Member
 
awelker's Avatar
 
Join Date: May 2010
Location: Berrysburg, PA
Posts: 49
Default Re: 8BA or 59AB to power belly tank at Bonneville

barnfind - Thanks for the compliment, years of planning and packaging that all gets wrapped in a body where you see none of it.
__________________

www.vonwelker.com

https://www.flickr.com/photos/vonwelker/albums
Home of the Blonde Bitch Bellytank
awelker is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:00 AM.