|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-06-2017, 04:36 AM | #1 |
Senior Member
Join Date: Feb 2012
Location: Gladstone QLD Australia
Posts: 324
|
33 Grille Shell Emblim
Hi all,
Well I received my Ford script emblem for the 33 from C&G, made by Vintique. I was a little concerned before I installed it and only tightened the nut just over finger tight and put some sealer on the thread to stop it vibrating off. Next morning the Ford script was laying on the floor. It looked as though the fastener was glued onto the script plate. Very poor reproduction. Anyone else had any problems ?. |
05-06-2017, 05:42 AM | #2 |
Senior Member
Join Date: Apr 2011
Location: Plainview, Texas
Posts: 757
|
Re: 33 Grille Shell Emblim
Junktique strikes again. Hate that for you. Watch ebay, and find an original.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-06-2017, 06:02 AM | #3 |
Senior Member
Join Date: May 2010
Posts: 4,751
|
Re: 33 Grille Shell Emblim
I have not found a source for originals but consider usinga couple dabs of RTV to adhere the emblem to the top of the grill trim. You can remove it and any RTV if you happen to find an original.
|
05-06-2017, 06:57 AM | #4 |
Senior Member
Join Date: May 2010
Posts: 13,690
|
Re: 33 Grille Shell Emblim
I had the same experience with the Vintique junk one. Found it on the floor a couple of days later.
|
05-06-2017, 07:35 AM | #5 |
Senior Member
Join Date: Jun 2011
Location: South Dakota
Posts: 405
|
Re: 33 Grille Shell Emblim
I also had same problem. The fastener came off with minimal tightening of the nut. Put it back on with crazy glue which so far holding Ok 3 years later
|
05-06-2017, 09:06 AM | #6 |
Senior Member
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,651
|
Re: 33 Grille Shell Emblim
Sponsored Links (Register now to hide all advertisements)
JB weld to the rescue, been on for three years now. |
05-06-2017, 10:37 AM | #7 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: 33 Grille Shell Emblim
Mine fell of but busted the enamel. I got them to send a new one. So far, so good.
|
05-06-2017, 05:57 PM | #8 |
Senior Member
Join Date: Feb 2012
Location: Gladstone QLD Australia
Posts: 324
|
Re: 33 Grille Shell Emblim
Thanks guys, thought it may have been me.
I will resort to JB weld or something similar. Kpar |
05-06-2017, 05:58 PM | #9 |
Senior Member
Join Date: Feb 2012
Location: Gladstone QLD Australia
Posts: 324
|
Re: 33 Grille Shell Emblim
just a thought, is Bob Drakes any better ?.
|
05-06-2017, 07:47 PM | #10 |
Senior Member
Join Date: Jun 2012
Location: Long Island,NY
Posts: 1,555
|
Re: 33 Grille Shell Emblim
I had a Bob Drakes snap off and lost the emblem somewhere. When I told Bob Drake about it at Hershey, he asked me if I put any Silicone adhesive behind it. Sure Bob, I guess old Henry used silicone also!
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|