Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-27-2017, 02:03 AM   #1
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Post war replacement blocks for 81a

Hi guys,
It's been awhile since I last logged on...

I have a post war replacement block for an 81a motor that has a 3/16th bore and is also factory relieved. My question is, how far can these be bored out. One cylinder has a nasty gouge (about 50 thou) from a gudgeon (wrist) pin circlip coming loose and a piece of the pin broke off and gouged the bore.

I don't need or want this block, so I'm wondering if there is any demand for these things, or is it just scrap value. The block is in New Zealand so V8 blocks are not as plentiful as the US.

Thanks.
Fe26 is offline   Reply With Quote
Old 03-27-2017, 05:12 AM   #2
Jay in Mass
Senior Member
 
Join Date: May 2010
Location: Mass.
Posts: 379
Default Re: Post war replacement blocks for 81a

I would not scrap it. Someone somewhere needs it.
Jay in Mass is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-27-2017, 06:00 AM   #3
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 4,725
Default Re: Post war replacement blocks for 81a

Ford installed hard steel sleeves in some of the 81A blocks you can do just one cylinder for repair.
Terry,OH is offline   Reply With Quote
Old 03-27-2017, 11:18 AM   #4
flatheadmurre
Senior Member
 
flatheadmurre's Avatar
 
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
Default Re: Post war replacement blocks for 81a

Boring all out large or installing a sleeve and boring to next oversize is about the same amount of time so i would sleeve one cylinder if the rest looks good.
Going for 239 is working to if you want more displacement.
If the block is not badly rusted itīs a keeper !!
flatheadmurre is offline   Reply With Quote
Old 03-27-2017, 01:47 PM   #5
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Post war replacement blocks for 81a

Your size dimension is a question mark for me. Is it 3 1/16 standard bore for 41A block or is it already out to 3 3/16 oversize? These have relatively thin walls but they will go out to 3.1875" as a general rule. If more than that I would get it sonic tested. If it is still near standard, the bore might clean up on that scored wall. If not, it would be worth sleeving as others have already mentioned.
rotorwrench is offline   Reply With Quote
Old 03-27-2017, 05:10 PM   #6
jetmek
Senior Member
 
Join Date: May 2010
Location: albany
Posts: 462
Default Re: Post war replacement blocks for 81a

Sponsored Links (Register now to hide all advertisements)
Post war replacement blocks ive seen are 59A castings with small bore....if so definitely a keeper...
__________________
engine and component overhauls my specialty!
Website- www.godevilgarage.com
jetmek is offline   Reply With Quote
Old 03-27-2017, 06:06 PM   #7
deuce_roadster
Senior Member
 
deuce_roadster's Avatar
 
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,777
Default Re: Post war replacement blocks for 81a

I have a 59 series long block that was cast in 1953 (stenciled on crate) that is 3 3/16 that came out of a Ford dealership in Texas in 1958. It had 8ba rods, cap screws on mains and 51 crankshaft. I left the bore at 3 3/16, put in a 4" crank and Ross pistons with the skinny rings. This motor is going into a 40 V8 business coupe with 4bbl, and Columbia rear end.
deuce_roadster is offline   Reply With Quote
Old 03-27-2017, 08:56 PM   #8
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,843
Default Re: Post war replacement blocks for 81a

Quote:
Originally Posted by deuce_roadster View Post
I have a 59 series long block that was cast in 1953 (stenciled on crate) that is 3 3/16 that came out of a Ford dealership in Texas in 1958. It had 8ba rods, cap screws on mains and 51 crankshaft. I left the bore at 3 3/16, put in a 4" crank and Ross pistons with the skinny rings. This motor is going into a 40 V8 business coupe with 4bbl, and Columbia rear end.
That's a great story. I'm glad you kept it at 3 3/16. Seems the market today is for boring right past all the oversizes and going straight to maximum for the series. I know the skeptics say there won't be a 'next generation' of flatheaders, but I know a few guys in their thirties who are living the flathead dream. We have to leave something for them to put oversize pistons in.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is offline   Reply With Quote
Old 03-28-2017, 01:42 AM   #9
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Re: Post war replacement blocks for 81a

Quote:
Originally Posted by Jay in Mass View Post
I would not scrap it. Someone somewhere needs it.
Thanks Jay, I needed to hear that, seems a shame to scrap it.
Fe26 is offline   Reply With Quote
Old 03-28-2017, 01:44 AM   #10
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Re: Post war replacement blocks for 81a

Quote:
Originally Posted by Terry,OH View Post
Ford installed hard steel sleeves in some of the 81A blocks you can do just one cylinder for repair.
It would be so easy if this block did have sleeves but it doesn't. Someone may put there hand up for it.
Fe26 is offline   Reply With Quote
Old 03-28-2017, 01:46 AM   #11
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Re: Post war replacement blocks for 81a

Quote:
Originally Posted by flatheadmurre View Post
Boring all out large or installing a sleeve and boring to next oversize is about the same amount of time so i would sleeve one cylinder if the rest looks good.
Going for 239 is working to if you want more displacement.
If the block is not badly rusted itīs a keeper !!
Will these blocks go out for 239? If so it has real potential. There is no rust on this block. As I understand it this was a truck application, hence the factory relieving. I was thinking the only use for this block was if someone wanted to fit a Supercharger. The question then becomes how far can it be bored.

Last edited by Fe26; 03-28-2017 at 01:55 AM.
Fe26 is offline   Reply With Quote
Old 03-28-2017, 01:49 AM   #12
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Re: Post war replacement blocks for 81a

Quote:
Originally Posted by jetmek View Post
Post war replacement blocks ive seen are 59A castings with small bore....if so definitely a keeper...
Yes it is the replacement block but it doesn't have the 59A letters on it. I heard that some US made replacement blocks were designated 41A. But this one would have come from Canada as a Commonwealth countries export.
Fe26 is offline   Reply With Quote
Old 03-28-2017, 02:30 AM   #13
1932tub
Senior Member
 
Join Date: May 2010
Location: Nelson New Zealand
Posts: 157
Default Re: Post war replacement blocks for 81a

I have a couple of these blocks , both 3 3/16th 60 thou over, you should have plenty of meat left.
1932tub is offline   Reply With Quote
Old 03-28-2017, 10:27 AM   #14
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
Default Re: Post war replacement blocks for 81a

That should be a C51A block unless it's a prewar C81A casting. They made them for a while after the war but we seldom hear much about them. I don't think the prewar Canadian blocks had the raised casting numbers on the front of the block like they did on the post war C59A and C69A blocks. It would be interesting to know if it has a raised casting ID on there.

The US designation was 41A for the post war 221 blocks and they had many characteristics of the prewar 81A block but most have the 59 on the bell. I think they used pewar type sand cores from the old engines inside the core boxes for the 59 series blocks for production casting. How they could ID them at the factory before painting is a mystery to me. You have to know the characteristics to tell them apart.

Last edited by rotorwrench; 03-28-2017 at 10:48 AM.
rotorwrench is offline   Reply With Quote
Old 03-28-2017, 06:59 PM   #15
Fe26
Senior Member
 
Join Date: May 2010
Location: Sydney, Australia
Posts: 949
Default Re: Post war replacement blocks for 81a

Thank you gentlemen, you have been very helpful.
Fe26 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:50 AM.