Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-14-2020, 10:22 PM   #1
Mad Mac
Senior Member
 
Join Date: Mar 2013
Location: New Zealand
Posts: 364
Default Steering wobbe

I am trying to diagnose the cause of a slight wobble in the steering of my 1929 RPU. This is not the dreaded “death wobble” but more a tendency to wander at cruising speed. There is no play at all in the 7-tooth steering box and pitman arm (checked on the bench with a dial guage) and the steering column is bolted tightly to the frame. Therefore I assume the problem lies “downstream” of the pitman arm, probably in the drag link and/or tie rod connections. I will investigate them shortly, but in the meantime I want to eliminate other possible causes that could be cheaper and easier to fix.

Just recently I did two things that seemed to worsen it: I pumped both front tyres up to 35psi and repacked the bearings in the LHS wheel. I tightened the wheel nut as per recommendations in this forum, so am hoping it is tight enough. I would be grateful for any further suggestions
Mad Mac is offline   Reply With Quote
Old 05-14-2020, 10:53 PM   #2
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: Steering wobbe

What were the recommendations of this forum to tighten the wheel nut?

Charlie Stephens
Charlie Stephens is online now   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-14-2020, 11:29 PM   #3
nomadpsd
Member
 
nomadpsd's Avatar
 
Join Date: Jul 2018
Posts: 49
Default Re: Steering wobbe

What is the toe-in set at? Incorrect Toe (especially toe-out) can cause wandering.
nomadpsd is offline   Reply With Quote
Old 05-15-2020, 08:24 AM   #4
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: Steering wobbe

Ck toe-in. How old are the tires??
Why only repack one side wheel bearing??
Paul in CT
1931 flamingo is offline   Reply With Quote
Old 05-15-2020, 08:45 AM   #5
daren007
Senior Member
 
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
Default Re: Steering wobbe

Alignment.
daren007 is offline   Reply With Quote
Old 05-15-2020, 08:50 AM   #6
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Steering wobbe

Sponsored Links (Register now to hide all advertisements)
I also think that toe in could be the problem . check and set the toe in at 1/16 .
Purdy Swoft is offline   Reply With Quote
Old 05-15-2020, 09:40 AM   #7
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Steering wobbe

If everything is tight and wheels are straight/true I agree with toe-in.


Worried about the wheel bearing adjustment. Easy. Tighten nut while spinning wheel/drum just enough to make sure it just snug, back nut off to next or 2nd castle making sure wheel still spins freely. Install cotter.
Patrick L. is offline   Reply With Quote
Old 05-15-2020, 10:31 AM   #8
Tacoma Bob
Senior Member
 
Tacoma Bob's Avatar
 
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
Default Re: Steering wobbe

In my case after changing out everything over the course of several years it was the spring perch nuts. Driver side was loose by 2.5 turns. Passenger side 3/4 of a turn. Snugged em down very tightly and and no more wobble.
Tacoma Bob is offline   Reply With Quote
Old 05-15-2020, 10:45 AM   #9
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Steering wobbe

Quote:
Originally Posted by Tacoma Bob View Post
In my case after changing out everything over the course of several years it was the spring perch nuts. Driver side was loose by 2.5 turns. Passenger side 3/4 of a turn. Snugged em down very tightly and and no more wobble.
I hope that you verified that you have the proper nuts on there, the ones with the taper of the end that fits into the radius rod. And don't forget the cotter pins.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 05-15-2020, 11:28 AM   #10
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Steering wobbe

Often the cause of wobble is looseness in the drag link ends. Check that and I recommend 1/8" toe in. Wheel bearings should be tightened very snug, rotate wheel a few times, then back off nut and re-tighten just enough to take out all the free-play. Check both wheels. Tie rod ends should be snug too. Wandering can be caused by castor and/or camber being off a little.
Jim Brierley is offline   Reply With Quote
Old 05-15-2020, 03:53 PM   #11
Mad Mac
Senior Member
 
Join Date: Mar 2013
Location: New Zealand
Posts: 364
Default Re: Steering wobbe

Quote:
Originally Posted by Patrick L. View Post
If everything is tight and wheels are straight/true I agree with toe-in.


Worried about the wheel bearing adjustment. Easy. Tighten nut while spinning wheel/drum just enough to make sure it just snug, back nut off to next or 2nd castle making sure wheel still spins freely. Install cotter.
Yeah, thats what I did
Mad Mac is offline   Reply With Quote
Old 05-15-2020, 06:02 PM   #12
Tacoma Bob
Senior Member
 
Tacoma Bob's Avatar
 
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
Default Re: Steering wobbe

Katy....you betcha! My initial fear is that the taper had wallowed but so far so good. I went through hell until I figured it out. I replaced everything imaginable. One of out club tech guys asked me if there was rust outside of the boss's. Prior to figuring things out there was indeed rust where there had not been prior.
Tacoma Bob is offline   Reply With Quote
Old 05-15-2020, 08:33 PM   #13
Mulletwagon
Senior Member
 
Mulletwagon's Avatar
 
Join Date: Jan 2019
Location: Florida Panhandle
Posts: 585
Default Re: Steering wobbe

Jack up the front end under the axle and try to rock the wheels both 3-9, 6-12, and straight up and down. Any loose joints or king pin slop will be obvious. Also rotate the wheels to check for run out or other signs of a warped/bent rim. Please share the fix when you figure it out.
Mulletwagon is offline   Reply With Quote
Old 05-15-2020, 11:06 PM   #14
Mad Mac
Senior Member
 
Join Date: Mar 2013
Location: New Zealand
Posts: 364
Default Re: Steering wobbe

Quote:
Originally Posted by Charlie Stephens View Post
What were the recommendations of this forum to tighten the wheel nut?

Charlie Stephens
Hi Charlie,
To tell you the truth, the recommendations were a little confused and contradictory, but the gist of it was that the nut should be tightened until the wheel starts to bind and then back off a quarter turn or to the nearest castellation hole for the split pin. Not too tight and not too loose, just like Goldilocks.
Mad Mac is offline   Reply With Quote
Old 05-15-2020, 11:09 PM   #15
Mad Mac
Senior Member
 
Join Date: Mar 2013
Location: New Zealand
Posts: 364
Default Re: Steering wobbe

Quote:
Originally Posted by Patrick L. View Post
If everything is tight and wheels are straight/true I agree with toe-in.
I had the toe-in checked at the local wheel alignment shop and they say it is good. However I'm not sure how much they know about Model A Fords.
Mad Mac is offline   Reply With Quote
Old 05-16-2020, 07:09 AM   #16
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Steering wobbe

Quote:
Originally Posted by Mad Mac View Post
I had the toe-in checked at the local wheel alignment shop and they say it is good. However I'm not sure how much they know about Model A Fords.


Your statement about wheel bearings is about right. 1/4 turn back off may be a bit much. Not to tight and not too loose is correct


Toe-in is pretty much toe-in. Its pretty much a fits all. All cars need toe-in and the amount is usually 1/32- 1/8". Those numbers also work for an 'A', I prefer 1/23-1/16".
Patrick L. is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:25 PM.