Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 02-27-2020, 02:12 AM   #1
Paul Bennett
Senior Member
 
Join Date: Sep 2016
Posts: 628
Default Alternator Reliability

I've seen several postings re: Powermaster Alternators working well yet quitting after a few years.

I'm wondering if high belt pressure causes front bearing failure. Any thoughts? or Alternative Alternators?

Should bearing failure indeed be a problem...has anyone found a solution?
Paul Bennett is offline   Reply With Quote
Old 02-27-2020, 04:55 AM   #2
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Alternator Reliability

Which model are you referring to ?
Have been running a GM alternator for over 20 years with no issues.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 02-27-2020, 05:56 AM   #3
PeteVS
Senior Member
 
PeteVS's Avatar
 
Join Date: May 2010
Location: FP, NJ
Posts: 2,769
Default Re: Alternator Reliability

Is it possible that an aftermarket alternator could be using low grade bearings to shave his costs to boost profit? Maybe it would be wise to buy an alternator and replace the bearing with a better quality piece from the get go. The fact that alternators carry only a low current through the brushes and those brushes contact a non-segmented rotating surface is what makes the alternator such a clear cut choice over a generator. You should also cut bearing load by reducing belt tension to only what is required at high charging currents.
__________________
Don't never get rid of nuthin!
PeteVS is offline   Reply With Quote
Old 02-27-2020, 08:58 AM   #4
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Alternator Reliability

Quote:
Originally Posted by Paul Bennett View Post
I've seen several postings re: Powermaster Alternators working well yet quitting after a few years.

I'm wondering if high belt pressure causes front bearing failure. Any thoughts? or Alternative Alternators?

Should bearing failure indeed be a problem...has anyone found a solution?
I'm currently using a Whitney alternator conversion, but haven't had it long enough to comment on life expectancy.
Attached Images
File Type: jpg Whitney Co.jpg (63.5 KB, 36 views)
JSeery is offline   Reply With Quote
Old 02-27-2020, 09:49 AM   #5
Bob/Pa
Senior Member
 
Bob/Pa's Avatar
 
Join Date: May 2010
Location: Oakmont, Pa (Longwood)
Posts: 297
Default Re: Alternator Reliability

Like Merc-51 been using for over 10 years, no problem, first one I used new had a humming noise so Powermaster sent me a new one and still going strong.
Bob/Pa is offline   Reply With Quote
Old 02-27-2020, 09:54 AM   #6
adileo
Senior Member
 
adileo's Avatar
 
Join Date: Jun 2014
Location: New Jersey
Posts: 1,772
Default Re: Alternator Reliability

Sponsored Links (Register now to hide all advertisements)
I have a 6v powermaster alt. In my 39 for over four years. No problems yet.

As for tight belt, I’d be more concerned with water pumps, than the alt.
__________________
Thanks

Andy
1952 F1
adileo is offline   Reply With Quote
Old 02-27-2020, 01:33 PM   #7
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: Alternator Reliability

13 yrs and no problem. Dang it seems like just yesterday .
Ggmac is offline   Reply With Quote
Old 02-27-2020, 02:55 PM   #8
drolston
Senior Member
 
drolston's Avatar
 
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,622
Default Re: Alternator Reliability

I ran a PowerMaster 12 volt generator-look-alike alternator which burned out after less than three thousand miles. The wiring and diodes failed, not the bearings. That look-alike alternator is really a small car alternator stuffed inside of the look-alike case. Probably does not ventilate as well as it should. I got it repaired by a good alternator shop, but do not expect long life from it.
drolston is offline   Reply With Quote
Old 02-27-2020, 03:47 PM   #9
G.M.
Senior Member
 
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
Default Re: Alternator Reliability

Quote:
Originally Posted by 51 MERC-CT View Post
Which model are you referring to ?
Have been running a GM alternator for over 20 years with no issues.
I had several GM alternators converted to 6 volts. The electric
motor company, Chestnut Hill Electric near Lancaster, Pa. suggested
they use a 24 volt stator and 6 volt diodes and an adjustable
voltage regulator. This allowed it to provide 7.2 volts at idle with
a LARGE 39 Ford pulley. On the 7 alternators I made the adjustable
voltage regulator was mounted inside the rear cover plate with a
hole through the cover plate to adjust the idle voltage. I had two of
them made 10 or more years ago and they still work good. We used
a 39 Ford front generator mount with the big bearing and had to
make a shaft adaptor for the front of the shaft for the pulley to mount
on. The last picture shows the long term end results of an over tight
fan belt. This pump was of a 35 Ford that belonged to a friend of
mines father. The two end covers were 2 of seven alternators I made
a number of years ago and all seven still work good. G.M.
Attached Images
File Type: jpg 100_0151.jpg (43.4 KB, 23 views)
File Type: jpg 100_0150.jpg (48.4 KB, 25 views)
File Type: jpg Alternator 39 CS.jpg (36.3 KB, 24 views)
File Type: jpg WATER PUMP WORN BUSHING.jpg (71.6 KB, 21 views)
File Type: jpg BELT-ADJ.jpg.jpg (29.0 KB, 17 views)
__________________
www.fordcollector.com
G.M. is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:52 AM.