Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-19-2019, 01:22 PM   #1
1936 ford pickup
Member
 
Join Date: Feb 2015
Posts: 87
Default Wiper Motor Mtg. Hardware needed....

Hello,


I have my '36 Ford pickup and need the Vacuum Wiper Motor Mtg. Hardware.
I had the Vacuum Wiper Motor rebuilt by Ficken Wiper Service.
Ficken Wiper Service did an excellent rebuild job.
Now I want to install into my '36 Ford Pickup.
I am trying to locate the required Mtg. Hardware.
Does anyone know where I can locate the required Mtg. Hardware.


Thank you,


Bruce in California
Attached Images
File Type: jpg 001.jpg (69.6 KB, 35 views)
1936 ford pickup is offline   Reply With Quote
Old 09-20-2019, 08:10 AM   #2
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 3,264
Default Re: Wiper Motor Mtg. Hardware needed....

Try Ficken or another rebuilder.
Terry,OH is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-20-2019, 09:01 AM   #3
deuce lover
Senior Member
 
deuce lover's Avatar
 
Join Date: May 2010
Location: Southern France
Posts: 2,941
Default Re: Wiper Motor Mtg. Hardware needed....

Kent of Clean Sweep in OR 541-923-4319 and Don't tell him Ficken did your wiper motor.
deuce lover is offline   Reply With Quote
Old 09-20-2019, 09:12 AM   #4
nelsb01
Senior Member
 
nelsb01's Avatar
 
Join Date: May 2010
Location: Up North
Posts: 196
Default Re: Wiper Motor Mtg. Hardware needed....

To answer your question --- the wiper is installed through the hole above the windshield. There is a special chrome washer (different than 1936 passenger vehicles) and then a nut. That is all that holds the wiper mechanism in. The rubber hose used for the vacuum that is needed to work the wiper runs down the drivers side A pillar (post) and under the dash and then through the wiring loom hole and to the intake manifold.
The special washer is hard to find. You may have to run a classifed wanted ad.
nelsb01 is offline   Reply With Quote
Old 09-20-2019, 11:45 AM   #5
1936 ford pickup
Member
 
Join Date: Feb 2015
Posts: 87
Default Re: Wiper Motor Mtg. Hardware needed....

THANK YOU very much to all of you for your replies back to me, they all helped a lot.
1936 ford pickup is offline   Reply With Quote
Old 09-20-2019, 07:00 PM   #6
DavidG
Senior Member
 
DavidG's Avatar
 
Join Date: May 2010
Posts: 6,090
Default Re: Wiper Motor Mtg. Hardware needed....

Bruce,


I'm sure you meant to mention the rubber washer encased in the special washer that served to seal the opening in the hole in the body roof.
DavidG is offline   Reply With Quote
Old 09-20-2019, 11:04 PM   #7
Don Rogers
Senior Member
 
Don Rogers's Avatar
 
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,330
Default Re: Wiper Motor Mtg. Hardware needed....

There is another major component that you will need to properly mount you wiper motor in your truck. You will need an internal spacer (50-811224) that goes between your wiper motor body and the inside og the cab roof. See images below.
Attached Images
File Type: jpg Truck wiper spacer.jpg (33.3 KB, 9 views)
File Type: jpg Truck wiper assembly small.jpg (80.8 KB, 28 views)
Don Rogers is online now   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:58 PM.