The Ford Barn

RockHillWill · 06-23-2011, 04:01 PM

Can some one tell me what the thread size is on a Stewart Warner horn armature ?

I am quite certain that it is left hand treads, but I cannot measure the diameter or threads on the broken one that I have.

I appreciate any information.

BRENT in 10-uh-C · 06-23-2011, 06:12 PM

Will, ...I totally forgot about that I was supposed to send you a couple of horns. If you recall, I told you that I needed you to send me an e-mail to remind me!!

I leave in the morning for San Diego. I can send you a S/W horn or two when I get back if you still need them by then.

.

RockHillWill · 06-23-2011, 06:41 PM

You're right, I forgot as well. I may have to learn to fix this issue. So far, I have heard of over 38 SW horns w/ broken armatures.

Bruce Lancaster · 06-24-2011, 09:46 AM

I believe that MSC industrial sells a range of LH taps and also taps in the odd thread sizes that appear some places on old Fords.

d.j. moordigian · 06-24-2011, 11:01 AM

Bruce,

I believe Will is looking for a die, which MSC should have as well.

Dudley

28 Special Coupe · 06-28-2011, 01:09 PM

Sponsored Links (Register now to hide all advertisements)

Quote:

Originally Posted by RockHillWill

You're right, I forgot as well. I may have to learn to fix this issue. So far, I have heard of over 38 SW horns w/ broken armatures.

Make it 39! I found out that they were left hand threads after I broke mine.

I had to glue the ratchet wheel on with JB Weld. It worked for a while until the windings started shorting out due to age.

RockHillWill · 06-29-2011, 05:52 AM

This seems to be a prevalent problem, so I guess I better try to figure a way to repair mine. Replacements are VERY hard to find and folks are quite proud of them if they have one.

So far I have identified the threads (thanks Don), acquired a tap and a die, ordered #8-32 left hand threaded rod from McMaster-Carr and have ordered the #27 (.144") tap drill.

I have been able to cut off the broken remains of the original threads and have cut a flat surface and cut in a 'starter drill' and am waiting for the tap drill to get here.

It is my intentions to tap a left hand thread, insert a piece of the threaded rod and loctite it in place.

28 Special Coupe · 06-29-2011, 11:59 AM

Sounds like a great plan. Unfortunately that exceeds my skill set. Please let us know how it turns out.

06-23-2011, 04:01 PM	#1
RockHillWill Senior Member Join Date: May 2010 Location: Rock Hill, S.C. Posts: 985	Stewart Warner Armature Threads Can some one tell me what the thread size is on a Stewart Warner horn armature ? I am quite certain that it is left hand treads, but I cannot measure the diameter or threads on the broken one that I have. I appreciate any information. __________________ Uncle Bud says "too soon old, too late smart!"

06-23-2011, 06:41 PM	#3
RockHillWill Senior Member Join Date: May 2010 Location: Rock Hill, S.C. Posts: 985	Re: Stewart Warner Armature Threads You're right, I forgot as well. I may have to learn to fix this issue. So far, I have heard of over 38 SW horns w/ broken armatures. __________________ Uncle Bud says "too soon old, too late smart!"

06-24-2011, 09:46 AM	#4
Bruce Lancaster Member Emeritus Join Date: May 2010 Location: Madison, NJ Posts: 5,230	Re: Stewart Warner Armature Threads I believe that MSC industrial sells a range of LH taps and also taps in the odd thread sizes that appear some places on old Fords.

06-24-2011, 11:01 AM	#5
d.j. moordigian Senior Member Join Date: May 2010 Location: Fresno, Ca. Posts: 3,636	Re: Stewart Warner Armature Threads Bruce, I believe Will is looking for a die, which MSC should have as well. Dudley

06-29-2011, 05:52 AM	#7
RockHillWill Senior Member Join Date: May 2010 Location: Rock Hill, S.C. Posts: 985	Re: Stewart Warner Armature Threads This seems to be a prevalent problem, so I guess I better try to figure a way to repair mine. Replacements are VERY hard to find and folks are quite proud of them if they have one. So far I have identified the threads (thanks Don), acquired a tap and a die, ordered #8-32 left hand threaded rod from McMaster-Carr and have ordered the #27 (.144") tap drill. I have been able to cut off the broken remains of the original threads and have cut a flat surface and cut in a 'starter drill' and am waiting for the tap drill to get here. It is my intentions to tap a left hand thread, insert a piece of the threaded rod and loctite it in place. __________________ Uncle Bud says "too soon old, too late smart!"

06-23-2011, 06:12 PM	#2
BRENT in 10-uh-C Senior Member Join Date: May 2010 Location: Eastern Tennessee Posts: 11,504	Re: Stewart Warner Armature Threads Will, ...I totally forgot about that I was supposed to send you a couple of horns. If you recall, I told you that I needed you to send me an e-mail to remind me!! I leave in the morning for San Diego. I can send you a S/W horn or two when I get back if you still need them by then. . __________________ . BRENT in 10-uh-C . www.model-a-ford.com ...(...Finally Updated!! ) .

06-29-2011, 11:59 AM	#8
28 Special Coupe Member Join Date: Jun 2010 Location: Broken Arrow, Oklahoma Posts: 63	Re: Stewart Warner Armature Threads Sounds like a great plan. Unfortunately that exceeds my skill set. Please let us know how it turns out.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode