|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-27-2020, 08:52 AM | #21 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
Re: My Distributor Cam Screw is Stuck
your way is a very sensible way in my opinion. Fix em in the garage instead of beside the road in a rain storm.
Last edited by McMimmcs; 11-27-2020 at 09:20 AM. |
11-27-2020, 09:30 AM | #22 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
Re: My Distributor Cam Screw is Stuck
Yes, sometimes money not spent is not money saved. Good advice on your part!
|
Sponsored Links (Register now to hide all advertisements) |
|
11-27-2020, 09:33 AM | #23 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: My Distributor Cam Screw is Stuck
It appears that the cam screw is stuck. I bet that's not your problem, It sounds more like your steering column rotated some. if you loosen the clamp on the steering box and the clamp inside the car you can rotate the column some to get your spark control quadrant where it needs to be..
|
12-01-2020, 10:52 PM | #24 |
Junior Member
Join Date: Feb 2017
Location: Utah, USA
Posts: 11
|
Re: My Distributor Cam Screw is Stuck
Success! While working on the distributor I saw evidence of what looked like red thread locker on several other fasteners. So I suspect that someone used red thread locker on the cam screw. As you know the red stuff is meant to be permanent. Supposedly it can be loosened by heating above 500 F, but I was afraid that applying that kind of heat could do other damage. So I decided to sacrifice the upper shaft. I pulled out the distributor, removed the sleeve, and pulled out the upper shaft with the stuck cam screw. Then I clamped the shaft in the drill press and drilled the top of the cam screw with progressively larger bits until the head separated from the screw shank. With the screw head gone, I was able to pull the aluminum magnet sleeve off undamaged. In the morning I will order a new upper shaft.
This has been a tremendous learning experience for me. Many thanks to everyone here who helped me get through this. Brian |
12-05-2020, 01:33 PM | #25 |
Senior Member
Join Date: Aug 2015
Location: Clermont in Central Florida
Posts: 111
|
Re: My Distributor Cam Screw is Stuck
This is what you say your problem is: "I need to adjust the timing so spark lever all the way up gives 0 degrees advance like it is supposed to."
Jack Shaft gave you the solution: "if you loosen the clamp on the steering box and the clamp inside the car you can rotate the column some to get your spark control quadrant where it needs to be." Rotate the column clockwise until the lever on the distributor reaches the end of the slot in the distributor while the quadrant is in the full up position. Tighten the column in place. Follow the instructions for setting the timing using the timing pin. The rotor should be at the point of just leaving number one cylinder contact. Counter clockwise rotation. |
12-05-2020, 06:49 PM | #26 |
Junior Member
Join Date: Feb 2017
Location: Utah, USA
Posts: 11
|
Re: My Distributor Cam Screw is Stuck
Sponsored Links (Register now to hide all advertisements)
|
12-05-2020, 10:10 PM | #27 |
Member
Join Date: Jan 2013
Location: Hickory Corners, Mi
Posts: 62
|
Re: My Distributor Cam Screw is Stuck
All have given you good methods to fix the problem.
I would pull the distributor, remove the pinned lower sleeve the remove the shaft with the cam on it. Replace the shaft and cam for $25.00 or so, retime it and take a ride. Now with the shaft in a vise try the methods given above plus take a punch and hammer and tap on an edge the screw. Heat, solvent, and square shafted screw drivers have always worked for me. With it out of the distributor you can also try turning the cam!! Good luck |
12-06-2020, 03:04 PM | #28 |
Senior Member
Join Date: Aug 2015
Location: Clermont in Central Florida
Posts: 111
|
Re: My Distributor Cam Screw is Stuck
Your right, the seven tooth is a solid welded unit, can't rotate it. When you get your parts follow the instructions for setting the points and you'll be good to go. I thought you had a two tooth steering box.
Enjoy the car! |
12-06-2020, 07:14 PM | #29 |
Member
Join Date: Jan 2013
Location: Hickory Corners, Mi
Posts: 62
|
Re: My Distributor Cam Screw is Stuck
Take the distributor out remove the lower sleeve and the shaft, buy a new cam and shaft for $25 or so. Replace it and drive your A
Work on the shaft/cam using all the ideas others have sent you Good luck and enjoy the ride. DRC |
|
|
Sponsored Links (Register now to hide all advertisements) |
|