|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-20-2017, 09:47 PM | #1 |
Junior Member
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
|
16 spline Slip yoke
I converted a 40 3 speed to an open driveshaft. Now I need a 16 spline slip yoke. I know it's been asked before, but never found a good answer. What years should I look for? Or where can I buy a new one. Some of the places I looked on the net were confusing. Does anybody have a link I can go to, even if it's E-Bay.
Thanks in advance, Dennis |
07-20-2017, 10:45 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 2,458
|
Re: 16 spline Slip yoke
H;i the original yokes are usually with the driveshafts,use a pressed in u joint. I have heard of a GM yoke that will work. the yoke is fixed by a bolt into the output shaft right? Others will jump in on this post. Newc
|
Sponsored Links (Register now to hide all advertisements) |
|
07-20-2017, 11:55 PM | #3 |
Senior Member
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
|
Re: 16 spline Slip yoke
I just picked up a NOS yoke from "barnfind08", contact him and see if he has another.
|
07-21-2017, 12:38 AM | #4 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, Calif.
Posts: 376
|
Re: 16 spline Slip yoke
1955 to 61 GM cast iron powerglide yoke.
|
07-21-2017, 09:07 AM | #5 |
Member
Join Date: May 2010
Posts: 55
|
Re: 16 spline Slip yoke
55 chev. power glide yoke will work .. A little longer but can be trimmed . I think the original is about an 1" shorter. I can check my pile and look when I get out in the shop .. Not too hard to locate for you I would think. Van
|
07-21-2017, 09:50 AM | #6 |
Junior Member
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
|
Re: 16 spline Slip yoke
Sponsored Links (Register now to hide all advertisements)
|
07-21-2017, 11:19 AM | #7 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,367
|
Re: 16 spline Slip yoke
The 21C-4841 was the first knuckle & plug (or slip yoke) for the open drive commercials and it was used from 1942 to 1952. It should be relatively common, especially when folks are swapping out the Dana Spicer stuff for something else.
|
07-21-2017, 12:17 PM | #8 |
Senior Member
Join Date: Aug 2010
Location: newark, delaware
Posts: 3,735
|
Re: 16 spline Slip yoke
I got one if your still looking. $45 shipped to your door. Its out of a 50 ford F1
|
06-12-2019, 12:37 PM | #9 |
Member
Join Date: Nov 2017
Location: Cleveland TN
Posts: 32
|
Re: 16 spline Slip yoke
Do you still have your 50 F1 16 spline slip yoke?
|
06-13-2019, 09:26 AM | #10 |
Junior Member
Join Date: Jul 2017
Location: Hesperia Ca
Posts: 4
|
Re: 16 spline Slip yoke
|
06-14-2019, 03:21 AM | #11 |
Senior Member
Join Date: May 2010
Location: tasmania
Posts: 221
|
Re: 16 spline Slip yoke
I think manual customline one fits
|
06-14-2019, 06:03 AM | #12 |
Senior Member
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,356
|
Re: 16 spline Slip yoke
We stock them.....it’s made to fit the regular passenger car transmission but will fit the short pickup trans like you have by trimming it down about an inch and a half. They have the same knuckle set up as the original Ford pickup driveshaft did.
__________________
VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com |
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|