Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-05-2015, 08:31 PM   #21
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by Tom Wesenberg View Post
Yep, as Al said..........I wonder if it will sound like a pair of John Deere tractors running together?

It will be interesting..........as well as a lot of work. What is the stroke?
I really do not know how it will sound, that will be part of the fun. The new chev V8 trucks run on 4 when they are going easy. I do think it will idle a little strange

Tom It will be 1 inch less. 3 1/4, but I will be able to gain RPMS, with my cylinder head. It will be interesting to see how it does.If it does not work out I will only be out my work and a few dollars for material. But the fun and what I learn will be worth it.
George Miller is offline   Reply With Quote
Old 10-05-2015, 08:39 PM   #22
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by AL in NY View Post
George, I don't think you can get a "smooth" firing order using the V8 90 degree crank. Depending on how you set up the valve timing, a 720 degree firing cycle would go 180-90-180-270 or 180-270-180-90. You can't get 180 degrees of crankshaft rotation between each of the 4 cylinders in the firing cycle. Seems to me the engine would run ruff.
Yes the firing will not be smooth. Like Tom said a John Deere, Also Harleys.
I did have a Couple John Deere when I was farming years ago.I also put a Harley 45 engine in my Cushman When I was 16 years old. We will see
George Miller is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-05-2015, 09:19 PM   #23
old car guy
Senior Member
 
Join Date: May 2010
Location: tampa fl
Posts: 194
Default Re: 5 main, chev, crankModel A engine

George very interesting project it doesn't matter that it can't be done only that you do it. All the fun is always what wasn't or could not work , was to make it yours good bad indifferent it's still a cool project . Keep the pictures rolling.
__________________
old car guy
old car guy is offline   Reply With Quote
Old 10-05-2015, 10:02 PM   #24
hardtimes
Senior Member
 
hardtimes's Avatar
 
Join Date: May 2010
Location: South California
Posts: 6,188
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by George Miller View Post
I know this is not for ever one, so don't look if you do not want to see a chev crank in a, A engine.

After a couple of years I'm back working on this engine. Today I started to make rods for this engine out of 7075 Alum. I made a wooden one first to make sure my math was right. If there is any interest I can post some pictures of making the rods along the way. This engine will be for my home built over head cylinder head.
Hey George,
Definite YES ! Lots of info and pictures on both rods and crankshaft fitment !!

That looks like A block. Any reason for using A , or was that what was available ?

Last edited by hardtimes; 10-05-2015 at 10:05 PM. Reason: .......
hardtimes is offline   Reply With Quote
Old 10-06-2015, 07:38 AM   #25
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by hardtimes View Post
Hey George,
Definite YES ! Lots of info and pictures on both rods and crankshaft fitment !!

That looks like A block. Any reason for using A , or was that what was available ?
That is what I had. It seems funny but after restoring 25 Model A's and doing a few engines for friends, I have never work on or seen a B engine.
George Miller is offline   Reply With Quote
Old 10-06-2015, 10:21 AM   #26
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: 5 main, chev, crankModel A engine

Sponsored Links (Register now to hide all advertisements)
Just as a side note, Buick 231 1975-77 v-6, made an odd fire engine that was somewhat rough at idle but very smooth on the highway. At the same time but for a longer duration, they made the "same" engine an even fire version. REALLY ROUGH was when a tech put on the wrong dist. cap. I drove them both as a dealer mechanic and I preferred the odd one.
100IH is offline   Reply With Quote
Old 10-06-2015, 10:39 AM   #27
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: 5 main, chev, crankModel A engine

A friend of mine ran a 5 cyl. hemi V8 at the Lakes to get into a certain cubic inch class. He said it did idle oddly but was smooth under power and higher RPM. Your project is interesting but I think you'll find the torque way down because of the smaller cubic inches.
Jim Brierley is offline   Reply With Quote
Old 10-06-2015, 11:54 AM   #28
Nathan_1929
Member
 
Nathan_1929's Avatar
 
Join Date: Mar 2015
Location: Saint Louis, Los Angeles
Posts: 82
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by George Miller View Post
Day one. The picture of putting in wrist pin holes. Also the wooden rod that I made to make sure my math was right. Also to make sure it cleared every thing in side the engine. The alum rods will be a little different in shape.
I'd suggest holding the endmill in a collet, not a drill chuck, and raising the table up more.

Is 7075 a suitable application for engine temps? Are you going to shot peen it? Heat treat it?
__________________
Nathan - 1929 Closed Cab Pickup, 1929 Tudor, 1930 Coupe, 1941 Pickup - Vintage BMW Motorcycle Collector/Mechanic
Nathan_1929 is offline   Reply With Quote
Old 10-06-2015, 01:45 PM   #29
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by Nathan_1929 View Post
I'd suggest holding the endmill in a collet, not a drill chuck, and raising the table up more.

Is 7075 a suitable application for engine temps? Are you going to shot peen it? Heat treat it?
Thanks for the advice, but I have been running a Mill for many years. The end mills only job is to open up the hole. By not using a collet I can change tools faster. The finish size will be done with a boring head.
George Miller is offline   Reply With Quote
Old 10-06-2015, 01:47 PM   #30
hardtimes
Senior Member
 
hardtimes's Avatar
 
Join Date: May 2010
Location: South California
Posts: 6,188
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by George Miller View Post
That is what I had. It seems funny but after restoring 25 Model A's and doing a few engines for friends, I have never work on or seen a B engine.
Hey George,
Wow, 'never' worked or seen B ! I'd have lost $ betting against that .
BTW..When you get time to add notes/information (tutorial) on how you add the extra two mains to a stock block !
hardtimes is offline   Reply With Quote
Old 10-06-2015, 02:05 PM   #31
rowens55
Senior Member
 
rowens55's Avatar
 
Join Date: Mar 2015
Location: woodland Ca
Posts: 333
Default Re: 5 main, chev, crankModel A engine

Some you fellas and your engineering skills NEVER ceases to amaze me!!! WAY kool project!! Rowen
__________________
Alive n kickin n mostly kickin!
rowens55 is offline   Reply With Quote
Old 10-06-2015, 02:13 PM   #32
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by hardtimes View Post
Hey George,
Wow, 'never' worked or seen B ! I'd have lost $ betting against that .
BTW..When you get time to add notes/information (tutorial) on how you add the extra two mains to a stock block !
Well I just cut out some pieces of metal and pinned and welded them in. Then made new main caps for a 5 mains. I looked for some pictures of the block when I was doing it. But could not find any.

Got the pictures for today but can not get them to up load.
George Miller is offline   Reply With Quote
Old 10-06-2015, 02:46 PM   #33
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

I finished the bore in piston pin end to day. Plus I put the face plate on the lathe with the fixture for boring the big end of the rod. But first have cut the bottom of the rod at the center line of the bore in the big end. Then drill the bolt holes. Will drill the bolt holes first. Then bolt it back together.

The 4 picture is the boring head for the finish bore.
Attached Images
File Type: jpg Finsh bore on piston pin end 001.JPG (154.3 KB, 274 views)
File Type: jpg Finsh bore on piston pin end 002.JPG (157.3 KB, 264 views)
File Type: jpg Finsh bore on piston pin end 003.JPG (152.8 KB, 258 views)
File Type: jpg Finsh bore on piston pin end 004.JPG (157.2 KB, 258 views)
File Type: jpg Finsh bore on piston pin end 005.JPG (153.0 KB, 277 views)
George Miller is offline   Reply With Quote
Old 10-06-2015, 03:14 PM   #34
Charlie Stephens
Senior Member
 
Join Date: May 2010
Location: Southern California
Posts: 7,017
Default Re: 5 main, chev, crankModel A engine

What Chevy engine are the crank and cam out of?

Charlie Stephens
Charlie Stephens is offline   Reply With Quote
Old 10-06-2015, 03:19 PM   #35
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by Ron W View Post
It looks like the center lines of #2 and #3 journals may be offset from the bores? I'm curious how you will handle that. Ron W
It is a V8 crank so two were together on one journal. IT Works out 1and2 go to the front of the journal and 3 and 4 go to the back of the journal. Will have to make some spacers for there.
George Miller is offline   Reply With Quote
Old 10-06-2015, 04:54 PM   #36
Ron W
Senior Member
 
Ron W's Avatar
 
Join Date: Jan 2011
Location: Central Me.
Posts: 260
Default Re: 5 main, chev, crankModel A engine

It's a very exciting project! I wish you the best with it. It seems there is no limit to what we will do to use the model A block. Ron W
Ron W is offline   Reply With Quote
Old 10-07-2015, 04:14 AM   #37
colin1928
Senior Member
 
colin1928's Avatar
 
Join Date: Mar 2013
Location: Australa Melbourne
Posts: 878
Default Re: 5 main, chev, crankModel A engine

George do you still have the engine with the 455 head ?
colin1928 is offline   Reply With Quote
Old 10-07-2015, 04:49 AM   #38
Charlville
Senior Member
 
Charlville's Avatar
 
Join Date: Nov 2012
Location: West Berkshire, United Kingdom
Posts: 368
Default Re: 5 main, chev, crankModel A engine

Very interesting, keep it coming
__________________
Kevin Flood
West Berkshire UK
Member MAFCGB, VHRA, SAH, Brooklands Trust
Sporadic progress on My 1929 Sport Coupe can be found here along with my blog
http://automotiveamerican.com/
Charlville is offline   Reply With Quote
Old 10-07-2015, 07:03 AM   #39
George Miller
Senior Member
 
George Miller's Avatar
 
Join Date: May 2010
Location: NC
Posts: 2,975
Default Re: 5 main, chev, crankModel A engine

Quote:
Originally Posted by colin1928 View Post
George do you still have the engine with the 455 head ?
No I sold that to a guy on ham a couple of years a go. I also had one with a 1928 chev head on a engine in a 1928 Ford pickup. I sold the truck with that on it.

Just have the over head that I made, which will go on this engine,
George Miller is offline   Reply With Quote
Old 10-07-2015, 10:37 AM   #40
redmodelt
Senior Member
 
redmodelt's Avatar
 
Join Date: May 2010
Location: Portland OR
Posts: 6,339
Default Re: 5 main, chev, crankModel A engine

Here is a first off Model T 5 main block before being fully machined.
http://www.mtfca.com/discus/messages...tml?1444223576
redmodelt is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:55 AM.