Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 06-30-2019, 11:03 AM   #1
Jerry in Shasta
Senior Member
 
Jerry in Shasta's Avatar
 
Join Date: Jun 2010
Location: (Old)Shasta (Redding) CA
Posts: 321
Default Toe-in

some where I've seen the name of devise for setting toe-in.
I'll be darned if I can find it now.


A body got an idea what I'm looking for.


Thanks JB
__________________
Connoisseur of Rust
Jerry in Shasta is offline   Reply With Quote
Old 06-30-2019, 12:26 PM   #2
JohnTee
Junior Member
 
Join Date: May 2010
Location: Clinton, Tennessee
Posts: 10
Default Re: Toe-in

Search for:
Duby toe‑in alignment gage
JohnTee is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-30-2019, 11:11 PM   #3
daveymc29
Senior Member
 
daveymc29's Avatar
 
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,293
Default Re: Toe-in

I made one out of curtain rod. Cut rod to about 1 1/2 inches short of the distance between the front tires inside edges and JB welded a small carriage bolt in one end. On the other end I slid a bolt and nut into the tube with the bolt threads having one wrap of masking tape on them and the end of the tube buffed clean of any paint. Slathered it up with JB Weld and when it had set for a couple of days I unscrewed the bolt, took the tape off it and put the bolt back into the nut and screwed it back in. To use, I run the car into the garage and stop, block the rear wheels and used the tool to determine the existing distance between the inside edges of the tires. I prop the tool up on two short lengths of 2 X 6 lumber so I get about five and a half inches up off the concrete. Then I loosen the tie rod ends and adjust the tie rod so I have about 1/8 inch more length between the rear of the two tires than at the front of them. Most tires have a little ledge cast into the sidewall and I try to stay right on that ledge with the front of the tires and 1/8 inch off it with the rears of the tires.. I mark the start spot with chalk and roll the car to get the tool on top of the 2 X 6 block at the rear. Takes a few minutes and you will have it aligned. Many have more expensive tools but they are no more accurate and I have several friends that use it whenever they work on their front ends. Total cost was about five dollars for the tube, JB Weld I always have on hand. Fix teeth and everything short of broken bones with it.
daveymc29 is offline   Reply With Quote
Old 06-30-2019, 11:34 PM   #4
PalAl
Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 75
Default Re: Toe-in

You can make this one sold by Bratton's out of PVC and a few nuts and bolts

https://www.brattons.com/front-axle-toe-in-tool.html
PalAl is offline   Reply With Quote
Old 07-01-2019, 04:42 PM   #5
eagle
Senior Member
 
eagle's Avatar
 
Join Date: Aug 2011
Location: Eagle Bend, MN
Posts: 1,448
Default Re: Toe-in

First make sure your wheels run true, then use a stick as described above or just a tape measure if you're careful.
__________________
"There are some that can destroy an anvil with a teaspoon and shouldn't be allowed to touch anything resembling a tool."
eagle is offline   Reply With Quote
Old 07-01-2019, 09:17 PM   #6
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 2,896
Default Re: Toe-in

NAPA years back
Attached Images
File Type: jpg aline2.jpg (30.9 KB, 23 views)
File Type: jpg aline1.jpg (89.0 KB, 30 views)
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Old 07-02-2019, 09:56 AM   #7
old31
Senior Member
 
Join Date: Jan 2016
Posts: 941
Default Re: Toe-in

I bought a stickie tape from Hobby Lobby for $2.39 and a shower curtain from Wallmart for about $10

Loosen tie rod bolts (9/16) on both the left and right side of the tie rods.

Do not make adjustments by turning spindles at end of tie rods, only the tie rods. On the right side tie rod turning the vice grip clockwise will decrease the measurement, counterclockwise will increase the measurement.

First, take the front tire measurement with shower rod with the car about 3 feet back. Front measurement must be 1/16 less than rear measurement. Thus, this will cause the toe in. / \

Second, pull the car forward so the rod will automatically be placed on the rear part of the tire. Read the tape and see what the toe in/out is.
Make adjustments while rod is still positioned on the rear of the tire.

Adjustment is done by clamping vise grip on tie rod and turning tie rod, either clockwise or counterclockwise. The turn is dependent if you need to adjust in or out. While turning tie rod you will see the shower rod moving on the scale on the shower rod.
After achieving the 1/16 toe in, do the process 1 more time as a double check.
Attached Images
File Type: jpg toein tool.jpg (72.4 KB, 16 views)
old31 is offline   Reply With Quote
Old 07-02-2019, 01:36 PM   #8
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,558
Default Re: Toe-in

Would a SCUFF-PLATE work ?
Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 07-02-2019, 01:46 PM   #9
jwilliams81
Senior Member
 
jwilliams81's Avatar
 
Join Date: Sep 2016
Location: Cincinnati OH
Posts: 313
Default Re: Toe-in

I bought this and find it a little easier to use than the Duby Gauge
https://www.summitracing.com/parts/lng-79620/overview/
__________________
1931 Murray Town Sedan. Black body with Apple Green pin stripe. Cincinnati, OH
jwilliams81 is offline   Reply With Quote
Old 07-02-2019, 04:16 PM   #10
ahirt
Member
 
Join Date: Nov 2014
Location: Stuart Florida
Posts: 69
Default Re: Toe-in

Google "Wheel-A-Matic" Toe -in Gauge. Same as Duby but lots cheaper. Got one and it works well.
ahirt is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:46 AM.