|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-09-2018, 09:02 PM | #1 |
Senior Member
Join Date: May 2010
Posts: 886
|
Need some distributor lessons
I have a 41 ford v-8 distributor Is this the most preferred and what model do they call it an 11-A or 40-B ? it has the smaller cam than the earlier model , is the advance better than the earlier unit?
thanks Fordestes |
08-09-2018, 09:05 PM | #2 |
Senior Member
Join Date: May 2010
Location: NorCal
Posts: 2,617
|
Re: Need some distributor lessons
Fordestes
If you have a true 41 distributor, it will have the 11A advance mechanism in it. The advance mech is marked. It is IMO, the best to use. Jim |
Sponsored Links (Register now to hide all advertisements) |
|
08-09-2018, 09:17 PM | #3 |
Senior Member
Join Date: May 2010
Posts: 886
|
Re: Need some distributor lessons
the only numbers I can find on all three I have dis-assembled is 68, nothing else besides ford logo on the breaker plate. does 68 mean anything far as curve etc.?
|
08-09-2018, 11:12 PM | #4 |
Senior Member
Join Date: May 2015
Posts: 8,131
|
Re: Need some distributor lessons
68 was the Model Number for the 1936 Ford....
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
08-10-2018, 08:22 AM | #5 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: Need some distributor lessons
68 is a 22 degree unit as well.
I see no difference in a 68 and a 11A. As long as you have the small cam with indiviudal contacts thats the good one. |
08-10-2018, 09:49 AM | #6 |
Senior Member
Join Date: Jun 2014
Location: Salt Lake City, Utah
Posts: 756
|
Re: Need some distributor lessons
Sponsored Links (Register now to hide all advertisements)
|
08-10-2018, 02:40 PM | #7 |
Senior Member
Join Date: May 2010
Posts: 886
|
Re: Need some distributor lessons
Thank Bubba, I will proceed wit the cleaning and lube of the distributor, also what are the numbers for new points from napa and which condenser is a good one for trouble free operation?
|
08-11-2018, 02:24 PM | #8 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: Need some distributor lessons
CS47 for the point set
|
08-11-2018, 02:39 PM | #9 |
Senior Member
Join Date: May 2010
Location: Snohomish,WA
Posts: 1,030
|
Re: Need some distributor lessons
|
08-11-2018, 05:05 PM | #10 |
Senior Member
Join Date: May 2010
Posts: 886
|
Re: Need some distributor lessons
my dist .is a 37-41, v-8, has small cam and 68 on the internal components.
|
08-11-2018, 07:22 PM | #11 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: Need some distributor lessons
Jim school me as every single 68!dizzy I’ve ever strobed advances between 16-18 degrees compared to the 11a which always advances 21-24 degrees??
|
08-11-2018, 07:30 PM | #12 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Need some distributor lessons
The advance curve is different on the 68 to the 11a,
Lawrie |
08-11-2018, 07:58 PM | #13 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: Need some distributor lessons
Lawrie I know the curve is different but so is the amount it advances.
|
08-11-2018, 09:36 PM | #14 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Need some distributor lessons
I,m not home so can’t look up my stuff,but I think they advance to the same amount ,but at a different rate
Lawrie |
08-12-2018, 12:17 AM | #15 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: Need some distributor lessons
Lawrie,
On all I’ve ever done the base line on them all in terms of cam degree are as follows 40a 11 deg 40b 8 deg 68. 8 deg 99a (very rare) 10deg 11a 11 deg I personally think there is a notable improvement between the 68 and 11a. |
08-12-2018, 12:36 AM | #16 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Need some distributor lessons
In my ford service bulletin books it lists all the advance info!start degrees,finish degrees, total advance ,and there you see there is a big difference in them,as I said I,m away from home so can’t look up them.
B,it the 11a is the best of the two, Lawrie |
08-12-2018, 02:03 PM | #17 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: Need some distributor lessons
Mike , Will do as i have two apart going back together right now , just havent noticed much difference in the 68 and 11 As.......I have parts for both will get a run up this week and check again......
|
08-12-2018, 02:27 PM | #18 |
Senior Member
Join Date: May 2010
Posts: 886
|
Re: Need some distributor lessons
Thanks all who responded, Bubba we will be looking forward to the results
many thank for your effort. fordestes |
08-13-2018, 01:23 PM | #19 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: Need some distributor lessons
Guys got a few minutes this morning to look at a few parts.
I might have mis-spoke a little bit by saying the model 68 and the 11A were the same degrees?? Heres the Bulletins from the Ford Bible regarding all (but the 41 dist) and like Mike stated the 68 is rated at 18 degrees at 1900 rpm. Looking over the workbench this morning i have one of the 68 and a 11A unit going together this week. Will run the curves on the machine as time permits. Some observations and measurements show the cam assemblys, the two shafts and the brake rings. Appears the 11A and 68 cams ( small) weights etc are the same. Shaft slots measure the same as well, although may be slight variation in slot locations???? The two brake rings have different profiles and slots ( this could be the major difference in the two). Did Henry use the 11A in the 41 models and then carry the part into the 42 crab??? My books say very little in regars to 41-42 distributor changes????? |
08-13-2018, 03:03 PM | #20 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: Need some distributor lessons
Jim,
Thanks for your observations.. The only difference in my opinion in the 68 vs 11A weights is the spring tension. I believe ford redesigned the brake ring (or index plate as I call it), when they redesigned the shaft to allow more advance. I believe the shaft is all that controls the amount of advance, and weights natually control the rate. I have run a 11A index plate on a 68 distributor with no change, however running a 68 index plate on a 11A distributor limits the advance by two degrees. Somewhere I have the Ford prints and engineering drawings on the different distributor parts. The 21A distrubutor used the 11A weight and index plate with the only change being the shaft. What is that "901" distributor on the chart?? |
|
|
Sponsored Links (Register now to hide all advertisements) |
|