|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-28-2020, 08:39 AM | #41 |
Junior Member
Join Date: Jul 2020
Posts: 2
|
Re: repairing rear axle housing bearing races..
Meric42
I found the pictures and your explanation . Thanks Tony. |
07-28-2020, 10:02 AM | #42 | |
Senior Member
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
|
Re: repairing rear axle housing bearing races..
Quote:
|
|
Sponsored Links (Register now to hide all advertisements) |
|
07-28-2020, 11:47 AM | #43 |
Senior Member
Join Date: May 2010
Posts: 4,743
|
Re: repairing rear axle housing bearing races..
Columbia Two Speed has the good races!
|
07-28-2020, 03:18 PM | #44 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,990
|
Re: repairing rear axle housing bearing races..
Quote:
__________________
"I can explain it for you. However, I can't understand it for you". |
|
07-28-2020, 03:19 PM | #45 |
Senior Member
|
Re: repairing rear axle housing bearing races..
This is one I did a while back with a full bearing brought of the shelf , The hub race on the axle is a slid fit no machining needed except it needs a sleeve on the OD of the Axle . also a thin sleeve on the ID of the hub ,I have no significant miles on it as yet ,Merc 42 maybe a better way .
Last edited by FlatheadTed; 07-29-2020 at 12:27 AM. |
07-28-2020, 05:18 PM | #46 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: repairing rear axle housing bearing races..
Sponsored Links (Register now to hide all advertisements)
machine the hub bearing area true, press in a sleeve ,then machine to 80mm Have done two , the roller bearings take WAY more load than a ball bearing, the 2 NU 1010 take a static load of 9500 KGs per side so they will handle 19 tones on the back end . Also the speed of the rollers is way slower than a needle roller. BUT they are costly. I have a set on my bench now so will post some pics, or look up a post I did way back on them . Lawrie |
07-28-2020, 05:24 PM | #47 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,212
|
Re: repairing rear axle housing bearing races..
I don't know how to load the old post but is on 04-03-2017, 06:54 AM by Lawrie
|
07-28-2020, 09:40 PM | #48 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: repairing rear axle housing bearing races..
Here is the link Lawrie.
https://www.fordbarn.com/forum/showt...highlight=axle I have just done the second bearing repair mod for my spare 33 rear end. This fixes the worn bearing area in the hub and on the axle area also. I machined the hub out to 82.5 mm, then shrunk in a sleave, bored that to 80mm.The hub was easy to machine out after I used a new insert on the boring bar. BUT it is very hard. machine the axle OD down to 50mm and press on the bearing inner. The bearings are two roller ones with a total load capacity of 9.6 tons each side and a limiting speed of 9500rpm ,so should be safe there. Only draw back of this, I have to remove the brake drum from the hub to machine it as my lathe is not quite big enough to do it with it on. Lawrie |
|
|
Sponsored Links (Register now to hide all advertisements) |
|