Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-30-2019, 09:58 AM   #21
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: No spark?

Quote:
Originally Posted by Licensed to kill View Post
There is no solenoid for the starter. It's direct power form the battery (-), through a starter switch on the floor to the starter. Battery + to frame. I am using a jumper wire from the coil direct to the battery to eliminate any possible ignition switch/wiring issues.
So what is the output from the coil? As suggested, making and breaking the (+) side the of the coil should throw a spark. Disconnect the primary wire from the distributor and hold it a half inch or so from a good ground. Disconnect the coil to distributor wire ( the + side) and with the hot wire (-) connected to the coil, touch the (+) side of the coil wire to ground and remove. You should get a spark, if not something is wrong with the coil.
JSeery is offline   Reply With Quote
Old 03-30-2019, 10:06 AM   #22
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

Quote:
Originally Posted by JSeery View Post
So what is the output from the coil? As suggested, making and breaking the (+) side the of the coil should throw a spark. Disconnect the primary wire from the distributor and hold it a half inch or so from a good ground. Disconnect the coil to distributor wire ( the + side) and with the hot wire (-) connected to the coil, touch the (+) side of the coil wire to ground and remove. You should get a spark, if not something is wrong with the coil.
I'll give that a go and report back.
Licensed to kill is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-30-2019, 11:09 AM   #23
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

I just thought of something that may be relevant. While i had everything apart for the rebuild, while doing the dizzy, after stripping it down, I had sandblasted and painted the distributor body (it's a cast iron one) and, IIRC I'm pretty sure I primed the inside of the housing to prevent corrosion. Is it possible that I am not getting an electrical contact somewhere due to the paint?. If so, where is the likely contact failure?.
Licensed to kill is offline   Reply With Quote
Old 03-30-2019, 11:54 AM   #24
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: No spark?

The points have to have a path to ground through there moving in the distributor and the distributor itself has to be grounded to the block. That could well be the issue if there is not a clear path to ground for the distributor. Same applies to the capacitor.
Attached Images
File Type: gif circ_ic.gif (3.0 KB, 15 views)
JSeery is offline   Reply With Quote
Old 03-30-2019, 11:55 AM   #25
fordyford
Senior Member
 
Join Date: May 2010
Posts: 191
Default Re: No spark?

When you rebuilt the engine did you paint the timing cover and carefully put it on to avoid scratching the new paint? You may have insulated the distributor from ground.
fordyford is offline   Reply With Quote
Old 03-30-2019, 01:09 PM   #26
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

Sponsored Links (Register now to hide all advertisements)
So, I have ground from the points base plate to engine block so all seems good there. However, when testing the coil, we disconnected the + side (from the coil to dizzy) and put a jumper wire on the coil. With the coil feed wire disconnected from the dizzy and held close to ground and the - side connected to the - side of the battery, when we touch the jumper wire from the + side of coil to ground, IT sparks but there is no spark from the coil feed wire suggesting that there is no power to the dizzy from the coil. We tried two different feed wires and checked the resistance on the feed wires and they seem to be fine. I hope all that makes sense. Unless I'm misreading the test results, It seems to me that the coil is shot.
Licensed to kill is offline   Reply With Quote
Old 03-30-2019, 02:31 PM   #27
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: No spark?

There are three wires involved here, battery feed to - terminal on the coil, coil + terminal to dist (which you are shorting to ground to simulate opening and closing of the points) and the third wire is the heavy sparkplug type wire from the center of the coil you are holding near a good to check for spark.
JSeery is offline   Reply With Quote
Old 03-30-2019, 03:47 PM   #28
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

Yes. The heavy spark plug wire from the centre of the coil is what I am referring to as the "coil feed wire". I get no spark jumping to ground when I touch the + coil wire to ground. I get a spark at the jumper wire when it touches ground but nothing from the heavy coil feed wire. I tried two different coil feed wires to make sure that wasn't the problem.
Licensed to kill is offline   Reply With Quote
Old 03-30-2019, 06:08 PM   #29
Don
Senior Member
 
Don's Avatar
 
Join Date: May 2010
Location: Ashland KY
Posts: 1,159
Default Re: No spark?

If it ran before it should run now!you saidyou painted everything ,on inside of dist !remove pains andget a good coil and condenser!its not rocket science,think it thru!!!
__________________
DON P
Don is offline   Reply With Quote
Old 03-30-2019, 08:48 PM   #30
Bill OH
Senior Member
 
Join Date: May 2010
Posts: 423
Default Re: No spark?

I have installed a new condenser in a tuneup only to have a no start. And you may have paint under the condenser mounting tab. I would try the condenser that you used before the rebuild.
Bill OH is offline   Reply With Quote
Old 03-30-2019, 09:15 PM   #31
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

Quote:
Originally Posted by Bill OH View Post
I have installed a new condenser in a tuneup only to have a no start. And you may have paint under the condenser mounting tab. I would try the condenser that you used before the rebuild.
I did. I started with the condenser that worked before the rebuild but replaced it when I found I had no spark.
Licensed to kill is offline   Reply With Quote
Old 03-30-2019, 09:45 PM   #32
A bones
Senior Member
 
A bones's Avatar
 
Join Date: May 2010
Location: CLAYTON DE
Posts: 1,280
Default Re: No spark?

After clearing the ground path of any new paint, squirt degreaser onto the point contact pads. If, by chance any goo was on the feeler gauge it can cause a no start. Good Luck.

P. S. Some starting fluids (ether ) include cylinder lubricant.
__________________
Enjoy yer day. Tom
Hate can't fix what it started.

Last edited by A bones; 03-30-2019 at 09:56 PM. Reason: PS
A bones is offline   Reply With Quote
Old 03-31-2019, 12:15 AM   #33
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: No spark?

touches ground but nothing from the heavy coil feed wire
Just a thought , to get a spark from the heavy feed wire you need a condenser involved ,one wire to + side of the coil and the condenser body tag grounded ,If you have replaced the points and if not set correctly then it wont work specially if one or the other point set is closed all the time , at some point the circuit must be broken .With some point sets available now ( not USA ones ) its hard to set them ,you could try and block off one set with a piece of paper then flick the other set it should throw a spark of the heavy feed wire ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 04-05-2019, 11:07 AM   #34
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: No spark?

UPDATE. Had a buddy come over and we spent a few hours trouble shooting. Went from no spark, to intermittent, (weak, strong spark) to good spark and got it running. Can't say what we did to improve spark but got it running. However, (and this could be related), I started it yesterday to take it out of the shop and turn it around to put it on the lift and while turning around outside, it just up and quit. Wouldn't restart so I pushed it in the shop. Checked this morning and no spark. Bypassed the ignition system (jumper wire from coil to battery) and still no spark. Pulled the dizzy cap and found that the rotor had broken. Was obviously catching on the cap contacts so now i need a new rotor. Question, how do I "fit" the new rotor so it makes proper contact and does not "catch" the cap contacts? The contacts in the cap show clear evidence of the roar hating them. [IMG][/IMG]
Licensed to kill is offline   Reply With Quote
Old 04-05-2019, 01:19 PM   #35
BUBBAS IGNITION
Senior Member
 
BUBBAS IGNITION's Avatar
 
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
Default Re: No spark?

Quote:
Originally Posted by Licensed to kill View Post
UPDATE. Had a buddy come over and we spent a few hours trouble shooting. Went from no spark, to intermittent, (weak, strong spark) to good spark and got it running. Can't say what we did to improve spark but got it running. However, (and this could be related), I started it yesterday to take it out of the shop and turn it around to put it on the lift and while turning around outside, it just up and quit. Wouldn't restart so I pushed it in the shop. Checked this morning and no spark. Bypassed the ignition system (jumper wire from coil to battery) and still no spark. Pulled the dizzy cap and found that the rotor had broken. Was obviously catching on the cap contacts so now i need a new rotor. Question, how do I "fit" the new rotor so it makes proper contact and does not "catch" the cap contacts? The contacts in the cap show clear evidence of the roar hating them. [IMG][/IMG]
Just buzz some material off the rotor tip on a belt sander or file.......many rotor to cap hits are just caused by different brands etc.......
__________________
If it Makes Spark, we do it !!!!
www.bubbasignition.com
[email protected]
BUBBAS IGNITION is offline   Reply With Quote
Old 04-05-2019, 01:23 PM   #36
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: No spark?

That is a problem, but it would not keep the coil from producing a spark, it would just keep it from being distributed.
JSeery is offline   Reply With Quote
Old 04-05-2019, 04:04 PM   #37
BUBBAS IGNITION
Senior Member
 
BUBBAS IGNITION's Avatar
 
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
Default Re: No spark?

Another ( but related) point was made in one of the posts. To make spark and test the coil with a lead wire you must use a condensor in the circuit like the picture from above. Everyone should have a condensor wired with two clips and a wire ......
Attached Images
File Type: gif ign point.gif (3.0 KB, 12 views)
__________________
If it Makes Spark, we do it !!!!
www.bubbasignition.com
[email protected]
BUBBAS IGNITION is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:13 AM.