The Ford Barn

backrodebob · 06-28-2021, 08:46 PM

picked up a mallory duel points model # 2527501off ebay, I’d like to run 1 instead of 2, can one of you gurus tell me what to set gap and dwell to? also should there be any endplay?

Smitty · 06-29-2021, 08:38 AM

Bob, How does that flattie move your A along. Have considered putting one in my coupe.

Steve

jayvee34 · 06-29-2021, 09:03 AM

Quote:

Originally Posted by Smitty

Bob, How does that flattie move your A along. Have considered putting one in my coupe.

Steve

Around 1962 I had a 30 coupe with a 59AB engine, ran really well and strong.
My wife even drove it.

jayvee34 · 06-29-2021, 09:10 AM

Quote:

Originally Posted by backrodebob

picked up a mallory duel points model # 2527501off ebay, I’d like to run 1 instead of 2, can one of you gurus tell me what to set gap and dwell to? also should there be any endplay?

I set mine @ .015, don't know about the dwell, no end play on mine, timing
was set @ 4 degrees BTDC. Hope this helps.

tubman · 06-29-2021, 09:26 AM

Do you mean you'd like to run one set of points instead of two? If so, I can't help you, if not, read on.

I believe I have that same Mallory in my '51 (I'd have to check the exact numbers). When I set my points using the gap, the car didn't run very well. I ended up buying a used dwell meter and set the dwell to the Mallory specs (I think it was 36 degrees total; again I'll have to check) and it ran a lot better. You set each set of points individually by blocking the other set open and then check total and work from there; it took a bunch of fiddlin' IIRC. On a modified engine, I set the idle advance using a vacuum gauge. with the vacuum line (if any) plugged, I adjust the idle to give the highest vacuum and then retard it just a little bit. Then using an advance timing light, I check for total advance at speed. If it's in the low 20's, you're probably good. If not you're going to have to play with weights, etc. to get it right.

If this is the Mallory distributor i'm thinking of, there is a stepped plastic "key" that you insert into a slot in the breaker plate to set total advance, either to 22 degrees or 36 degrees. For a flathead the former is best.

I will try to dig out the instruction sheet for that distributor the next time I'm at my shop.

rotorwrench · 06-29-2021, 10:34 AM

Sponsored Links (Register now to hide all advertisements)

Running both sets of breakers will give better dwell time. This give the coil better field saturation. Running only one defeats that purpose.

Smitty · 06-29-2021, 12:22 PM

jayvee34

What did you use for drive train in the 30, steering etc? Stock frame, center member etc?
Steve

BUBBAS IGNITION · 07-01-2021, 07:25 PM

will not run well with only a single set of points ( not enough dwell)

06-28-2021, 08:46 PM	#1
backrodebob Member Join Date: Jul 2019 Location: Union City, CA Posts: 57	mallory picked up a mallory duel points model # 2527501off ebay, I’d like to run 1 instead of 2, can one of you gurus tell me what to set gap and dwell to? also should there be any endplay?

06-29-2021, 08:38 AM	#2
Smitty Senior Member Join Date: May 2010 Location: Boston North Shore Posts: 752	Re: mallory Bob, How does that flattie move your A along. Have considered putting one in my coupe. Steve

06-29-2021, 09:26 AM	#5
tubman Senior Member Join Date: Dec 2013 Location: Minnesota, Florida Keys Posts: 10,312	Re: mallory Do you mean you'd like to run one set of points instead of two? If so, I can't help you, if not, read on. I believe I have that same Mallory in my '51 (I'd have to check the exact numbers). When I set my points using the gap, the car didn't run very well. I ended up buying a used dwell meter and set the dwell to the Mallory specs (I think it was 36 degrees total; again I'll have to check) and it ran a lot better. You set each set of points individually by blocking the other set open and then check total and work from there; it took a bunch of fiddlin' IIRC. On a modified engine, I set the idle advance using a vacuum gauge. with the vacuum line (if any) plugged, I adjust the idle to give the highest vacuum and then retard it just a little bit. Then using an advance timing light, I check for total advance at speed. If it's in the low 20's, you're probably good. If not you're going to have to play with weights, etc. to get it right. If this is the Mallory distributor i'm thinking of, there is a stepped plastic "key" that you insert into a slot in the breaker plate to set total advance, either to 22 degrees or 36 degrees. For a flathead the former is best. I will try to dig out the instruction sheet for that distributor the next time I'm at my shop. Last edited by tubman; 06-29-2021 at 09:31 AM.

06-29-2021, 10:34 AM	#6
rotorwrench Senior Member Join Date: Jun 2010 Location: San Antonio, Texas Posts: 16,426	Re: mallory Sponsored Links (Register now to hide all advertisements) Running both sets of breakers will give better dwell time. This give the coil better field saturation. Running only one defeats that purpose.

06-29-2021, 12:22 PM	#7
Smitty Senior Member Join Date: May 2010 Location: Boston North Shore Posts: 752	Re: mallory jayvee34 What did you use for drive train in the 30, steering etc? Stock frame, center member etc? Steve

07-01-2021, 07:25 PM	#8
BUBBAS IGNITION Senior Member Join Date: May 2010 Location: SPEEDWAY INDIANA Posts: 4,148	Re: mallory will not run well with only a single set of points ( not enough dwell) __________________ If it Makes Spark, we do it !!!! www.bubbasignition.com [email protected]