Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-19-2018, 11:34 PM   #1
wrndln
Senior Member
 
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
Default Acetylene regulator

I think my Victor acetylene regulator of 30 years has given up the ghost. I was looking at acetylene regulators on eBay and there are a lot of cheap, I assume China made, regulators for $25 to $40. The Victor regulators are $100 and a lot higher. That is a big difference in prices. I am wondering if there is a big difference in the function of the regulators. I am an occasional user, mostly using the torch to heat rusted nuts and bolts to free them. If anyone has information on the cheaper ones as far as working OK or not, please post their experience.
Rusty Nelson
wrndln is offline   Reply With Quote
Old 03-19-2018, 11:41 PM   #2
BillCNC
Senior Member
 
BillCNC's Avatar
 
Join Date: Aug 2017
Location: SoCal Desert
Posts: 826
Default Re: Acetylene regulator

For what it's worth, I have a couple of Chinese regulators that I use for Argon and another for Acetylene. They have been working flawlessly for about 5 years now.

Regards
Bill
BillCNC is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-20-2018, 03:52 AM   #3
pooch
Senior Member
 
pooch's Avatar
 
Join Date: Sep 2010
Location: South Coast NSW Australia
Posts: 2,596
Default Re: Acetylene regulator

I ditched acetylene, now use LPG.

No bottle rent.
pooch is offline   Reply With Quote
Old 03-20-2018, 06:35 AM   #4
aermotor
Senior Member
 
Join Date: Mar 2015
Location: Greenville, SC
Posts: 1,099
Default Re: Acetylene regulator

Most welding supply stores can have them overhauled in the area of $100. I would check on that before purchasing what could be C'junk.

John
aermotor is offline   Reply With Quote
Old 03-20-2018, 08:35 AM   #5
Corley
Senior Member
 
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
Default Re: Acetylene regulator

There are single stage and dual stage regulators. If you want steady pressure control, like for welding, you will want a dual stage regulators. Some of the cheapies are ok, just make sure you get a dual stage.
Corley is offline   Reply With Quote
Old 03-20-2018, 08:44 AM   #6
wrndln
Senior Member
 
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
Default Re: Acetylene regulator

Sponsored Links (Register now to hide all advertisements)
I only use the gas welding outfit for heating rusted/frozen nuts and bolts. I never use the torch for welding (I failed a gas welding class long ago), brazing or cutting. In fact I have never used the cutting torch since I bought the welding set over 30 years ago. I have a Lincoln SP100 MIG w/Argon-CO2 gas welder that I do ALL my welding with and it works great. Does that mean a single stage is good enough for heating rusted fasteners, as it seems like it would?
Rusty Nelson
wrndln is offline   Reply With Quote
Old 03-20-2018, 09:22 AM   #7
noboD
Senior Member
 
Join Date: May 2010
Posts: 313
Default Re: Acetylene regulator

Quote:
Originally Posted by aermotor View Post
Most welding supply stores can have them overhauled in the area of $100. I would check on that before purchasing what could be C'junk.

John
Amen. Would you buy a Chinese fire extinguisher and expect it to save your life?
noboD is offline   Reply With Quote
Old 03-20-2018, 10:01 AM   #8
Bob Wright
Senior Member
 
Bob Wright's Avatar
 
Join Date: May 2010
Location: Southern,Maine
Posts: 141
Default Re: Acetylene regulator

Try the Garage Journal (sister site) great & knowable people.
Bob
Bob Wright is offline   Reply With Quote
Old 03-20-2018, 10:18 AM   #9
redmodelt
Senior Member
 
redmodelt's Avatar
 
Join Date: May 2010
Location: Portland OR
Posts: 6,339
Default Re: Acetylene regulator

Are you forgetting the Kidde recall! Just because it's made in the US does not mean it's good.
__________________
I know the voices aren't real but damn they have some good ideas!

Last edited by redmodelt; 03-20-2018 at 06:22 PM.
redmodelt is offline   Reply With Quote
Old 03-20-2018, 11:26 AM   #10
28
Member
 
Join Date: Sep 2017
Location: Costa Mesa, CA
Posts: 49
Default Re: Acetylene regulator

Craigslist is my go to. Just checked my area and you can get what you need for 25 to 65 bucks. Welding or tank suppliers may have some for cheap
28 is offline   Reply With Quote
Old 03-20-2018, 06:06 PM   #11
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Acetylene regulator

Single stage will work fine for most of us. The last pair of tanks I got both had leaking valves, and I lost well over $100 worth of gas in one month. I only got to use my torch for about 10 minutes. I never went back, and have since learned that welding shop is now out of business. Screwed again.
Tom Wesenberg is offline   Reply With Quote
Old 03-20-2018, 06:27 PM   #12
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Acetylene regulator

Probably just needs a new Diaphragm! (CHEAP!)
Bill Fixit
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 03-20-2018, 06:50 PM   #13
jw hash
Senior Member
 
jw hash's Avatar
 
Join Date: May 2010
Location: Auburn Washington
Posts: 2,550
Default Re: Acetylene regulator

Gauges are cheap compared to the cost of acetylene over time. if they do not work correctly or leak. buy good gauges, they will save you money in the long run and last for years.
jw hash is offline   Reply With Quote
Old 03-20-2018, 07:16 PM   #14
Phil Brown
Senior Member
 
Phil Brown's Avatar
 
Join Date: May 2010
Location: Santee Calif.
Posts: 491
Default Re: Acetylene regulator

Check with your local welding supply shop about getting rebuilt, might be less $ than you think
Phil Brown is offline   Reply With Quote
Old 03-20-2018, 07:38 PM   #15
wrndln
Senior Member
 
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
Default Re: Acetylene regulator

I checked with my local welding supply shop today. The fellow there said he could check the regulator with soapy water and see if it leaks. I am pretty sure it does, however it would be nice to know for sure. I think I may have lost some acetylene due to the leak. He said it was $70 to get the regulator repaired. The concern I have is, this is the third time I have had problem with the USA made acetylene regulator. The oxygen regulator has never had a problem.
Rusty Nelson
wrndln is offline   Reply With Quote
Old 03-20-2018, 08:23 PM   #16
Cool Hand Lurker
Senior Member
 
Cool Hand Lurker's Avatar
 
Join Date: May 2010
Location: So Minn
Posts: 1,564
Default Re: Acetylene regulator

Get a repair kit. Fix it yourself for $20. That is what I did and the regulator works fine now. Here is a link to Amazon but you can just do a Google search and come up with more parts suppliers.
https://www.amazon.com/s/?ie=UTF8&ke...l_6h2p7o49ny_b
Cool Hand Lurker is offline   Reply With Quote
Old 03-20-2018, 08:37 PM   #17
Keith True
Senior Member
 
Keith True's Avatar
 
Join Date: May 2010
Location: Epping N.H.
Posts: 2,969
Default Re: Acetylene regulator

I've had some problems with leaky tank valves lately.I could smell a little gas when the tanks were on,so I thought I had a regulator going bad.Sprayed tire soap on it and found the valve was weeping around the stem when open.It happened on two fresh tanks.Gas has gotten expensive.Acetylene-$148.Oxy_$68.70-30 argon mix-$111. When I got my first set of torches oxy was $8.and acetylene was $12.I also was making $1.60 an hour.
Keith True is offline   Reply With Quote
Old 03-20-2018, 11:32 PM   #18
Marvin/TN
Senior Member
 
Join Date: May 2010
Location: Chattanooga, TN area
Posts: 832
Send a message via AIM to Marvin/TN
Default Re: Acetylene regulator

Always back the adjustment it will help get a longer life out of the diaphragm which might be the only thing wrong with it. Take it apart and check the diaphragm for cracks. I have made diaphragms for my air regulators which are about the same thing from brass shim stock. I have seen plastic diaphragm's in regulators but all of mine have brass ones. I even made one out of a Gal thinner can a couple of times.
Marvin/TN is offline   Reply With Quote
Old 03-21-2018, 06:03 AM   #19
Res731
Senior Member
 
Res731's Avatar
 
Join Date: Jun 2014
Location: Westlake, ohio
Posts: 107
Default Re: Acetylene regulator

I had mine rebuilt at welding store for less then 100.
Res731 is offline   Reply With Quote
Old 03-28-2018, 09:14 PM   #20
TZBrown
Member
 
Join Date: Dec 2017
Location: Fenton Michigan
Posts: 43
Default Re: Acetylene regulator

Rebuild it yourself, Easy, cheaper than having it done, and Victor parts are available

https://www.youtube.com/watch?v=POU7Zc8ONOM
TZBrown is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:45 AM.