|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-21-2017, 11:16 AM | #1 |
Junior Member
Join Date: Oct 2016
Location: Vidor, Texas
Posts: 8
|
41 Ford Pickup cab question
Restoring a 1941 Ford Pickup and upon removing the hood, hood braces and fenders I have questions about the holes in the side of the cowl. I know the top two and the one in the very front is where the hood braces connect. My question is the other three (next to the curve), especially the lower one. I see a rubber bumper in the upper most one of the three, but what goes in the next one and the lower one.
|
01-21-2017, 12:33 PM | #2 |
Senior Member
Join Date: May 2010
Location: El Cerrito CA
Posts: 338
|
Re: 41 Ford Pickup cab question
That hole is where the inner fender panel bolts, rubber bumpers in the other two.
Last edited by 41PICUP; 01-21-2017 at 12:41 PM. Reason: add the picture |
Sponsored Links (Register now to hide all advertisements) |
|
01-21-2017, 01:31 PM | #3 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,108
|
Re: 41 Ford Pickup cab question
I'm lovin' that Duntov water heater. DD
|
01-21-2017, 04:52 PM | #4 |
Junior Member
Join Date: Oct 2016
Location: Vidor, Texas
Posts: 8
|
Re: 41 Ford Pickup cab question
Thanks, my inner finder was broken on both sided were it bolted to the cowl.anc the bolt holes on each side were ripped out. Was considering welding them up, but thought I better check first.
|
01-21-2017, 06:52 PM | #5 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Re: 41 Ford Pickup cab question
Not only the inner fender, but through into the fender itself.
I believe the two holes on the line of the fender (the rusty curve) have been added by a previous owner. The three holes along the lower edge of the surface are used by the bigger trucks except the rearmost one is used by the pickup also. Mine has had one extra hole drilled, but not the second extra one shown in the pic of the black cab. Mart. |
01-22-2017, 07:49 AM | #6 |
Junior Member
Join Date: Oct 2016
Location: Vidor, Texas
Posts: 8
|
Re: 41 Ford Pickup cab question
Sponsored Links (Register now to hide all advertisements)
|
01-22-2017, 10:30 AM | #7 |
Senior Member
Join Date: May 2010
Location: El Cerrito CA
Posts: 338
|
Re: 41 Ford Pickup cab question
Tex, you can get that bracket from Bob Drake, part number 01C-16094
|
01-22-2017, 10:50 AM | #8 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Re: 41 Ford Pickup cab question
Yeah, it's a sort of angled U bracket. One bolt into the cab, another bolt through the inner fender and fender.
Mart. |
01-23-2017, 01:51 AM | #9 |
Junior Member
Join Date: Mar 2014
Location: SoCal
Posts: 27
|
Re: 41 Ford Pickup cab question
C & G has that fender to cowel brace also. Just picked up 2 for my '41 pickup.
|
01-23-2017, 08:07 AM | #10 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,749
|
Re: 41 Ford Pickup cab question
41picup, You might already realise this, but the rearmost hinge arm needs to be sticking up. There may be enough play to allow it to swing up, but if you don't want to force it you might need to remove the hinge from the cowl to allow it to swing around the back. Mart. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|