Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-07-2020, 05:50 PM   #1
Magoo2
Member
 
Join Date: Nov 2017
Location: NJ
Posts: 61
Default Bearing caps

I’m trying to rebuild an extra model a engine I have. Everything seems to be in pretty good shape except the main bearing caps. They appear pretty worn. There were no shims. Does anyone make pre babbitted caps I could purchase and then use something like Timesaver to work in the caps or do I need to have the bearings repoured and line bored. As I said it’s an extra engine and I’m just doing it for something to keep me busy.
Magoo2 is offline   Reply With Quote
Old 12-07-2020, 07:43 PM   #2
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,088
Default Re: Bearing caps

I have known Model A people, get caps that were good from swap meets or motors, and doing minor adjustments to the caps. and were successful. And others fit with proper shims. It can be done. That's my take. Unless you find an engine builder that has spare caps,but as far as I know none that you can purchase from vendors.Might check your local clubs, they may have some not being used.
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-07-2020, 08:09 PM   #3
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Bearing caps

Yes ford mechanics fit bearings.Timesaver works well especially if its high speed babbit.Ive seen some you can fit with a sharp knife.
Jack Shaft is offline   Reply With Quote
Old 12-08-2020, 01:00 PM   #4
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Bearing caps

If the bearing material is good, you can "file" the caps to decrease clearance. Sandpaper or emery cloth on a very flat surface works well. I recommend using plastigage along the full length of the bearing to insure proper clearance along the whole length of the bearing.
Jim Brierley is offline   Reply With Quote
Old 12-08-2020, 01:11 PM   #5
redmodelt
Senior Member
 
redmodelt's Avatar
 
Join Date: May 2010
Location: Portland OR
Posts: 6,339
Default Re: Bearing caps

I done the cap replacement on my Model T using just repored caps, but that was before I knew what I know now. That engine lasted may years and miles.

That being said, because of crankshaft flex the babbitt in the center main gets more worn in the block then the 1 and 3 so you may not get a good fit. The other thing would be, offset. The replacement/used caps may not be bored the same so may have an offset to the ones in the block. If this is just to practice, go for it. Use it as a learning experience on fitting the crank.
In the Model T days, even with the KR Wilson setup, you could get the caps from Ford that were not bored. You would then poured the babbitt in the block and bore them both at the same time.
__________________
I know the voices aren't real but damn they have some good ideas!
redmodelt is online now   Reply With Quote
Old 12-08-2020, 01:17 PM   #6
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: Bearing caps

Sponsored Links (Register now to hide all advertisements)
I have carved main bearings to fit foreign caps, and when the babbitts in the block are out of round, it is an iterative chore with many trial fits.

If the center main bearing is wornout, the crankshaft likely needs straightening before any bearing work is done, so salvaging main bearings is not practical.
Another concern is the thrust face on the rear main bearing. If it is not possible to get the crankshaft axial play within 0.010", again it is not practical to salvage the main bearings.
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:00 AM.